manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 248

9.14 Oil Filtration / Cooling

9.14.1 Engine oil filter – Replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Filter wrench

F30379104

Engine oil
Oil filter

(→ Spare Parts Catalog)

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Replacing engine oil filter

1.

Remove engine oil filter using the filter
wrench.

2.

Clean the sealing surface on the connecting
piece.

3.

Check sealing ring (1) of new engine oil filter
and apply a thin coat of engine oil.

4.

Check inscription on filter: must be “Oil Fil-
ter”.

5.

Screw on and tighten engine oil filter by
hand.

6.

Replace other engine oil filters in the same
way.

Note:

See label (2) on filter housing.

7.

Crank engine on starting system without in-
jecting fuel (→ Page 191).

8.

Check engine oil level (→ Page 242).

246 | Oil Filtration / Cooling | MS150093/05E 2018-12

TIM-ID: 0000000933 - 014

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands