manualshive.com logo in svg

MTU 20V 4000 L62, Operating Instructions Manual

Share
Download
MTU 20V 4000 L62 Operating Instructions Manual Download Page 151

7.3.6 Spark plug connector – Cleaning and check

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Spark plug connector with ignition cable

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

WARNING

Compressed air gun ejects a jet of pressurized air.
Risk of injury to eyes and damage to hearing, risk of rupturing internal organs!
• Never direct air jet at people.
• Always wear safety goggles/face mask and ear defenders.

Spark plug connector – Cleaning and check

1.

Remove spark plug connector (→ Page 150).

2.

Remove spark-plug isolator sealing ring (→ Page 152).

3.

Check spark plug connector (1) and ignition
line (2) visually for kinks, pinching points and
brittleness, replace if necessary.

4.

Check connection between upper section of
insulation (3) and lower section of insula-
tion (4) for firm seating, tighten hand-tight if
required.

5.

Blow out connection opening to spark plug
with compressed air.

6.

Check connection to spark plug visually. The
connection spring (5) must be free of parti-
cles.

7.

Check the ohmic resistance of the ignition
line at the two end connections (5) and (6).
The measured value must be within the ac-
ceptable range for the relevant spark plug
connector.

8.

Install spark-plug isolator sealing ring
(→ Page 152)

9.

Install spark plug connector (→ Page 152).

MS150034/04E 2016-11

| Ignition System | 151

TIM-ID: 0000070448 - 001

Summary of Contents for 20V 4000 L62







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands