MTU 12 V 4000 L62FB Operating Instructions Manual Download Page 166

Page: 166 / 181

7.10.4 Mixture coolant ‒ Filling

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Fluids and Lubricants Specifications (A001061/..) are available.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Mixture coolant

WARNING

Coolant is hot and under pressure.
Risk of injury and scalding!
• Let the engine cool down.
• Wear protective clothing, gloves, and goggles / safety mask.

NOTICE

Cold coolant in hot engine can cause thermal stress.
Possible formation of cracks in the engine!
• Fill / top up coolant only into cold engine.

Engine coolant ‒ Filling

Fill with treated coolant using a pressure pump until the system filling pressure, fuel-optimized (→ Page 27)
has been reached.

Vent mixture coolant circuit via system.

Start the engine and operate it at idle speed for some minutes.

Check coolant level (→ Page 163).

166 | Low-Temperature Circuit | MS150098/02E 2016-11

TIM-ID: 0000045246 - 001

Summary of Contents for 12 V 4000 L62FB






















































































































































































Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands

MTU 12 V 4000 L62FB, Operating Instructions Manual

Search results

Summary of Contents for 12 V 4000 L62FB

Reviews:

Related manuals for 12 V 4000 L62FB

Brands by name

Popular brands