manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 152

8.12 Belt Drive

8.12.1 Drive belt – Condition check

Preconditions

☑

Engine is stopped and starting disabled.

WARNING

Exposed rotating parts can eject drawn-in components or draw in body parts.
Risk of crushing, limbs or extremities may be pinched, trapped or entangled!
Risk of injury due to flying parts!
• Install rotating components at a suitable distance from other components.
• Never operates the engine without protective covers or safety guards which meet applicable accident

prevention regulations.

• Ensure that the safety guards can prevent body parts from being drawn in by rotating components.

Drive belt condition check

1.

Remove cover for belt drive.

2.

Checking drive belt condition:

Item

Findings

Action

Drive belt

Singular breakages (A)

None

Drive belt

Breakages on entire circumfer-
ence (B)

Replace drive belt (→ Page 153).

Drive belt

Material chipped (C)

Drive belt

Belt is oily, shows signs of over-
heating

3.

Install cover for belt drive.

152 | Belt Drive | MS150100/06E 2017-08

TIM-ID: 0000078308 - 001

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands