manualshive.com logo in svg

mru SWG100 CEM, User Manual, Page: 88 / 155

Share
Download
mru SWG100 CEM User Manual Download Page 88

MRU GmbH 

                                                  SWG 100 User Manual 

 

Page 

88

 of 

155

 

 
 

9.

 

Operating the analyzer 

 
This chapter has the follow structure: 

•

 

In the first part it will be explained, how to start the analyzer and the selftest menu. 

•

 

Part three shows the submenu, which are listed at the EXTRA menu. 

•

 

Part four shows the store menu. 

9.1.

 

General process of the measurement cycle 

 
 

 

 

 

 
 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

START 

Self test 

Self test ok? 

No 

Main menu measurement 

F2: Storage  

F3: Extras 

 

 

 
 
 

Yes 

1 

2 

Selftest 

Main menu  
measurement 

       Self test (see in this chapter) 

END 

1 

2 

       Main menu measurement                                                                                                           
(see in this chapter) 

Summary of Contents for SWG100 CEM




























































































































































Reviews:

No comments