mru SWG100 CEM User Manual Download Page 105

Page: 105 / 155

MRU GmbH

SWG 100 User Manual

Page

105

155

9.4.

Update the firmware

The analyzer and different installed options can be updated, if it is necessary. Following options

can be updated:

•

The firmware from the analyzer.

•

The firmware from the pcb- mainboard.

•

The firmware from the NDIR-bench.

•

The firmware from the installed I/O modules.

General steps for the firmware-update

Copy the actual firmware for the analyzer or the firmware from the option on a SD-

card. Be sure, that the firmware is in the mean root of the SD-card. All firmware

updates have the ending “fwb”.

Put the SD-card on the card slot on the operation unit. The card slot can be found

inside the door (see sketch below).

If the SD-card is recognized, the analyzer will make a noise.

Open the path:

XTRA

EVICE

NFO

. Dependent from the firmware update it can be

necessary to open the different submenus.

Update the analyzer (Firmware-

Updates with filename “1106.fwb”)

Open the path:

XTRA

EVICE

NFO

Press

F2 = details

to open the details for the main device menu.

BEEP!!

Summary of Contents for SWG100 CEM




























































































































































Search results

Summary of Contents for SWG100 CEM

Reviews:

mru SWG100 CEM, User Manual, Page: 105 / 155

Search results

Summary of Contents for SWG100 CEM

Reviews: