HO Gauge Synchronized
Diesel Sound Decoder
with 12 Sound Functions
Item #0001626
Thank you for purchasing our highly advanced DCC
locomotive decoder. Combined with any DCC System, our
decoder will make your model railroad more realistic and
exciting.
•
Synchronized diesel rumble with random sounds
•
1.5 amp capacity
•
Programmable for either 2-digit (1-127) or 4-digit
(1-9999) addresses
•
Programmable start voltage
•
Programmable acceleration rate
•
Programmable deceleration rate
•
Programmable top voltage
•
Programmable 14, 28, 128 speed steps
•
Directional lighting, (FO) at 0.2 amp rate
•
Programmable “Rule 17” directional lighting
•
Programmable for either ditch lights, mars light, or
strobe light
•
programmable different horns and bells
•
12 accessory sound functions (F1-F12)
•
Supports advanced consisting (CV19)
•
Supports programming on the main
•
Compatible with NMRA DCC standards
•
NMRA 8 pin plug included for easy installation
•
Complies with the part 15 of FCC
•
20mm speaker included
•
Dimensions: 50.0mm x 17.5mm x 6.0mm
NOTE: Due to limitations in older DCC Systems, somes of the sound
functions or light effects functions may not be able to be accessed. ALSO, you
might be limited to factory default CV values.
ADDITIONAL INFORMATION
The MRC 1626 HO gauge synchronized diesel sound decoder should perform
well when used with other brand command systems. See your DCC command
stations manual to learn how to program and operate the decoder. For more
information about register/CVs and their functions, please refer to the NMRA
DCC Standard & Recommended practices, RP-9.2.2 this is available directly
from the NMRA or their website at www.nmra.org.
FCC COMPLIANCE
This device complies with the part 15 of FCC rule. Operation is subject to the
following two conditions. (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interfer-
ence that cause undesired operation.
RETURN PROCEDURE
If it should become necessary to return your decoder, unplug the decoder and
return the decoder only. Please include a letter (printed clearly) with your
name, address, a daytime telephone number, and a detailed description of the
problem you are experiencing. Please also include a $15.00 check for handling
and shipping fee. Be certain to return the decoder only.
Send the decoder to:
Model Rectifier Corporation
Attn: Parts & Service
80 Newfield Avenue
Edison, NJ 08837-3817 U.S.A
PROGRAMMING
This decoder supports all programming methods including register, page CV,
direct CV and programming on the main (OPS mode programming).
2004 MODEL RECTIFIER CORPORATION
80 NEWFIELD AVENUE
EDISON, NJ 08837-3817
Tel. 732-225-6360
PRINTED IN USA
CV
Register
Description
Range
Factory
Value
CV1
R1
Short addres s
1-127
3
CV2
R2
Start voltage
0-32
0
CV3
R3
Acceleration
0-32
0
CV4
R4
Deceleration
0-32
0
CV5
---
Maximum voltage
0-32
0
CV29
R5
Bas ic configuration
---
2
CV7
R7
Manufacturer vers ion number
---
32
CV8
R8
Manufacturer ID
---
143
CV17
---
Long addres s upper byte
192-231
192
CV18
---
Long address lower byte
0-255
3
CV19
---
Advanced consist addres s
1-127
0
CV50
---
Horn type
0-2
1
CV51
---
Bell type
0-2
1
CV52
---
Horn volume
0-31
31
CV53
---
Bell volume
0-31
31
CV54
---
Dies el volum e
0-31
31
CV55
---
Brake volume
0-31
31
CV56
---
Dynanic brake volum e
0-31
31
CV57
---
Brake release volum e
0-31
31
CV58
---
Air pump volume
0-31
31
CV59
---
Coupling volume
0-31
31
CV60
---
Conductor volume
0-31
31
CV61
---
Reverser
0-31
31
CV62
---
Exhaust
0-31
31
CV63
---
Sand release volume
0-31
31
CV64
---
Air releas e volume
0-31
31
CV105
---
Us er identification number
0-255
0
CV106
---
Us er identification number
0-255
0
---
R6
Page number
0-31
1
CV112
---
Light effects
see chart
0
CV113
---
Ditch/mars light rate
0-48
10
CV114
---
Strobe light rate
0-48
10
CV115
---
Brake squeal
0=off, 1=on
0