MR VACUTAP VR Installation And Commissioning Instructions Download Page 67 | Manualshive

Page: 67 / 268

MR VACUTAP VR Installation And Commissioning Instructions Download Page 67

5 Assembly: Standard design

Maschinenfabrik Reinhausen GmbH 2015

67

4349315/00 EN

VACUTAP® VR®

4.

Residual pressure of no more than 10

-3

bar.

Vapor-phase drying in the transformer tank

For vapor-phase drying in the transformer tank, you have to open the kero-
sene drain plug before drying so that the kerosene condensate can drain
from the oil compartment.

The kerosene drain plug is located in the oil compartment base and is not
generally accessible from the outside. For this reason, you first have to re-
move the diverter switch insert, open the kerosene drain plug, and then in-
stall the diverter switch insert again. After the drying process, you have to re-
move the diverter switch insert again to close the kerosene drain plug.

NOTICE

Damage to the on-load tap-changer!

Damage to the on-load tap-changer and oil suction pipe due to incorrect or-
der of installation.
► Strictly adhere to the order of installation. Make sure to always install

the diverter switch insert before inserting the oil suction pipe into the oil
compartment.

Removing diverter switch insert

Before you can remove the diverter switch insert, you have to move the on-
load tap-changer into the adjustment position and remove the on-load tap-
changer head cover, tap position indicator, and oil suction pipe.

Before you can remove the diverter switch insert, you have to move the on-
load tap-changer into the adjustment position and remove the on-load tap-
changer head cover, tap position indicator, tap-change supervisory control,
and oil suction pipe.

5.7.2

5.7.2.1

«
...
65
66
67
68
69
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands