MR VACUTAP VR Installation And Commissioning Instructions Download Page 52 | Manualshive

Page: 52 / 268

MR VACUTAP VR Installation And Commissioning Instructions Download Page 52

5 Assembly: Standard design

Maschinenfabrik Reinhausen GmbH 2015

52

4349315/00 EN

VACUTAP® VR®

Connecting tap selector take-off leads

Proceed as follows to connect the tap selector take-off leads:
1.

NOTICE!

Screw tap selector take-off lead to connecting piece with care.

Comply with specified tightening torque and secure screw connection.
Failure to do so may result in damage to the on-load tap-changer and
transformer.

2.

Attach screening caps to screw connection.

Figure 35: Tap selector take-off lead

Connecting tap winding and on-load tap-changer take-off
lead

NOTICE

Damage to the on-load tap-changer!

Connecting leads which place mechanical strain on the on-load tap-changer
will damage the on-load tap-changer!
► Produce connections with care.
► Do not twist connection contacts.
► Connect connecting leads without warping or deforming.
► If necessary use an expansion loop for connecting leads.
► Fit screening caps provided to screw connections.

The tap winding and on-load tap-changer take-off lead must be connected in
accordance with the connection diagram included with the delivery.

Tap selector connection contacts VRC/VRE

The selector connection contacts are indicated on the selector bars, have
crimped ends and a through-hole for M10 screws to allow the selector take-
off leads to be connected by means of cable shoes.

5.2.5

5.3

5.3.1

«
...
50
51
52
53
54
...
»

Summary of Contents for VACUTAP VR













































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands