manualshive.com logo in svg

MR TAPCON 230 AVT, Operating Instructions Manual

Share
Download
MR TAPCON 230 AVT Operating Instructions Manual Download Page 107

9 Operation

Maschinenfabrik Reinhausen GmbH 2021

107

7817454/02 EN

TAPCON

®

 230 Expert

Setting

Behavior

Auto/manual blocking

▪ The 

Reversal of power flow

 event is issued.

▪ If Z compensation is activated, this function is deacti-

vated.

▪ Automatic regulation is blocked.

▪ You cannot perform tap-change operations in manual

mode.

Target tap position

▪ The 

Reversal of power flow

 event is issued.

▪ If Z compensation is activated, this function is deacti-

vated.

▪ The device triggers a tap-change operation to the tap

position you defined in the "Target tap position" pa-
rameter.

▪ The device blocks further tap-change operations.

▪ The target-tap-position operation is ignored if there is

no tap-position capture. Automatic regulation is
blocked.

Table 40: Behavior in the event of a reversal of power flow

9.2.6 TAPCON® 2xx retrofit

The TAPCON® 2xx retrofit function allows you to operate the device in par-
allel operation with existing devices. Parallel operation with the following ex-
isting devices is supported:

▪ Predecessor devices: TAPCON® 230 pro/expert

▪ TAPCON® 240

▪ TAPCON® 250

▪ TAPCON® 260

▪ TRAFOGUARD® with "Voltage regulation" options package

If you wish to operate several devices in parallel operation with existing de-
vices, you have to activate the TAPCON® 2xx retrofit function on each de-
vice.

Figure 47: Parallel operation of 2 devices with one TAPCON® 2xx

Summary of Contents for TAPCON 230 AVT







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands