manualshive.com logo in svg

MR OILTAP R, Installation And Commissioning Instructions, Page: 21 / 206

Share
Download
MR OILTAP R Installation And Commissioning Instructions Download Page 21

3 Product description

Maschinenfabrik Reinhausen GmbH 2015

21

4427410/00 EN

OILTAP® R

Figure 4: Position of name plate

 

Drive shaft

Function description

The drive shaft is the mechanical connection between motor-drive and on-
load tap-changer head / off-circuit tap-changer head.

The bevel gear changes the direction from vertical to horizontal (see drawing
892916).

Accordingly, the vertical drive shaft has to be mounted between drive and
bevel gear and the horizontal drive shaft between bevel gear and on-load
tap-changer or off-circuit tap-changer.

Setup/models of drive shaft

The drive shaft consists of a square tube and is coupled by two coupling
brackets and one coupling bolt at both ends to the drive / driven shaft end of
the device to be connected.

3.3

3.3.1

3.3.2

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments