MR OILTAP R Installation And Commissioning Instructions Download Page 17 | Manualshive

Page: 17 / 206

MR OILTAP R Installation And Commissioning Instructions Download Page 17

3 Product description

Maschinenfabrik Reinhausen GmbH 2015

17

4427410/00 EN

OILTAP® R

Product description

This chapter contains an overview of the design and function of the product.

Scope of delivery

The product is packaged with protection against moisture and is usually de-
livered as follows:
▪

Oil compartment with on-load tap-changer head and built-in diverter
switch insert

▪

Selector

▪

Motor-drive unit

▪

Drive shaft with coupling parts and bevel gear

▪

Protective device

▪

Technical files

Please refer to the delivery slip for full details of scope of delivery.

Single-phase on-load tap-changers are also available as an on-load tap-
changer set with a common motor-drive unit.

Note the following information:
▪

Check the shipment for completeness on the basis of the shipping docu-
ments.

▪

Store the parts in a dry place until installation.

▪

The product must remain in its airtight, protective wrapping and may on-
ly be removed immediately before installation

You will find more information in the "Packaging, transport, and storage"
[

30] chapter.

On-load tap-changer

Function description

On-load tap-changers are used to adjust the transmission ratio of transform-
ers without interrupting the load flow. Fluctuations in voltage occurring in the
power transmission grid, for example, can therefore be compensated for. For
this purpose, on-load tap-changers are fitted in transformers and connected
to the active part of the transformer.

A motor-drive unit, which receives a control impulse (e.g. from a voltage reg-
ulator), changes the on-load tap-changer's operating position, as a result of
which the transmission ratio of the transformer is adapted to the operating
requirements.

3

3.1

3.2

3.2.1

«
...
15
16
17
18
19
...
»

Summary of Contents for OILTAP R















































































































































































































Reviews:

No comments