MR ECOTAP VPD 3 30D-24 Page 76 Operating Instructions Manual Download

Page: 76 / 132

7 Operation

Maschinenfabrik Reinhausen GmbH 2021

8209941/00 EN

ECOTAP

VPD

III 30D-24 / MD&C

Figure 50: Regulation function response

1 + B%: Upper limit

2 U

desired

: Desired value

3 - B%: Lower limit

4 Set delay time T

5 U

actual

: Measured voltage

6 B%: Tolerance bandwidth

A U

actual

is outside the bandwidth. De-

lay time T starts.

B U

actual

is back within the bandwidth

before delay time T is complete.

C U

actual

is outside the bandwidth. De-

lay time T starts.

D U

actual

is still outside the bandwidth

when delay time T is complete.
Tap-change operation is initiated.

7.4.1.1 Desired voltage (P1)

You can use this parameter to set the desired value for voltage regulation.
To do so, proceed as follows:

The AVR MANUAL operating mode is active.

1. Press

until the desired parameter is displayed.

2. Press

to confirm the selection.

3. Press

to select the desired value.

4. Press

to confirm the selection.

5. Press

to save the setting.

Summary of Contents for ECOTAP VPD 3 30D-24





































































































































Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Related manuals for ECOTAP VPD 3 30D-24

Brands by name

Popular brands

MR ECOTAP VPD 3 30D-24, Operating Instructions Manual

Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Related manuals for ECOTAP VPD 3 30D-24

Brands by name

Popular brands