MR ECOTAP VPD 3 30D-24 Operating Instructions Manual Download Page 75

Page: 75 / 132

7 Operation

Maschinenfabrik Reinhausen GmbH 2021

8209941/00 EN

ECOTAP

VPD

III 30D-24 / MD&C

8. Mount the motor-drive unit.

9. Connect the connectors to the terminals X4, X2 and X1 on the control

unit.

7.4 Configuring the control unit

This chapter describes how to configure the control unit.

Settings are only saved once the parameterization menu is exited via the

key. If you do not press the

key within 30 s, the parameterization

menu is exited automatically and the changes are not saved.

7.4.1 Regulation

All of the parameters required for the regulation function are described in this
section.

In AVR AUTO auto mode, voltage regulation works as follows:

▪ If the measured voltage U

actual

is within the set bandwidth

, no control

commands are issued to the motor-drive unit for the tap-change opera-
tion.

▪ Control commands will also not be issued to the motor-drive unit if the

measured voltage returns

to the tolerance bandwidth within the set de-

lay time T1

▪ However, if the measured voltage deviates from the set bandwidth for a

longer period

, a tap-change command

occurs after expiration of the

set delay time. The on-load tap-changer carries out a tap-change in a
raise or lower direction to return to the tolerance bandwidth.

Summary of Contents for ECOTAP VPD 3 30D-24





































































































































Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Brands by name

Popular brands

MR ECOTAP VPD 3 30D-24, Operating Instructions Manual

Search results

Summary of Contents for ECOTAP VPD 3 30D-24

Reviews:

Brands by name

Popular brands