Moxa Technologies NPORT 6610 Quick Installation Manual Download Page 1

 

 

– 1 – 

– 2 – 

– 3 – 

P/N: 1802066500013 

NPort 6600 Series   

Quick Installation Guide 

   

 

F

if

th Edition, 

March

 2011 

1.

 

Overview 

The NPort 6600 series of serial device servers includes 8-port, 
16-port, and 32-port models for connecting larger numbers of 
serial devices to Ethernet. Some applications now also require 
better security when transmitting data through a network. The 
NPort 6600 series of device servers use DES, 3DES, and AES data 
encryption to provide secure network communication. 

2.

 

Package Checklist 

Before Installing your NPort 6600 series secure device server, 
verify that the package contains the following items: 

 

1 NPort 6600 device server 

 

CBL-RJ45M9-150: 8-pin RJ45 to DB9 male connection cable, 
150 cm 

 

Power Cord (AC models only) 

 

2 rack-mount ears 

 

Documentation and software CD 

 

Quick installation guide (printed) 

 

Warranty card 

Optional Accessories

 

 

DK-35A: 35 mm DIN-Rail Mounting Kit 

 

DIN-Rail Power Supply 

 

NM-TX01/NM-TX01-T: Network module with one 
10/100BaseTX Ethernet port (RJ45 connector; supports 
cascade redundancy) 

 

NM-FX01-S-SC/NM-FX01-S-SC-T: Network module with one 
100BaseFX single mode fiber port (SC connector; supports 
cascade redundancy) 

 

NM-FX02-S-SC/NM-FX02-S-SC-T: Network module with two 
100BaseFX single mode fiber ports (SC connectors; supports 
cascade redundancy) 

 

NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one 
100BaseFX multi mode fiber port (SC connector; supports 
cascade redundancy) 

 

NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two 
100BaseFX multi mode fiber ports (SC connectors; supports 
cascade redundancy) 

 

NM-GPRS/GSM: GPRS/GSM modem module 

 

NM-Modem/NM-Modem-T: One PSTN modem port with RJ11 
connector 

 

NOTE: Please notify your sales representative if any of the above 
items is missing or damaged. 

3.

 

Hardware Introduction 

Demonstrated 8 port model to be an example. 

 

Reset button 

Press the Reset button continuously for 5 sec to load factory 
defaults

Adjustable pull high/low resistor for RS-485 (150 K

 or 1 

K

The NPort 6650 has 3 DIP Switches associated with each serial port 
for configuring the pull high/low resistors for RS-485 applications. 
The switches are located in a recess on the bottom of the NPort 
6650. To access the switches, first remove the panel covering the 
recess. 

: Use a pointed object to press the reset button. Release 

the button after the Ready LED stops blinking. 

 

SW  1 

Pull High  Pull Low  Terminator 

ON  1 K

 

1 K

 

120 K

 

OFF  150 K

 

150 K

  --- 

 

NOTE:

 

For RS-232 applications, all DIP Switches for the port 

should be set to the OFF position. 

Rack Mounting 

Use four screws to attach the NPort 6610/6650 to a standard rack 

 

LED Indicators 

Name 

Color 

Function 

PWR 

Red 

Power is being supplied to the power input. 

Ready 

Red 

Steady 
on: 

Power is on and the NPort 6600 
series is booting up. 

Blinking:  IP conflict, DHCP or BOOTP server 

not responding, or relay output. 
Check relay output first. If still 
blinking, then there is an IP 
conflict, or the DHCP or BOOTP 
server did not respond properly. 

Green 

Steady 
on: 

Power is on and the NPort 6600 
series is functioning normally. 

Blinking:  The device server has been 

located by the Administrator’s 
Locator function. 

Off 

Power is off, or power error condition exists. 

Link 

Orange  10 Mbps Ethernet connection. 
Green 

100 Mbps Ethernet connection. 

Off 

Ethernet cable is disconnected, or has a 
short. 

P1-P16 Tx  Green 

Serial port is transmitting data. 

Off 

No data is being transmitted through the 
serial port 

P1-P16 Rx  Orange  Serial port is receiving data.. 

Off 

No data is being received through the serial 
port. 

FX 

Orange  Steady on: 

Ethernet fiber connection, 
but port is idle. 

Blinking: 

Fiber port is transmitting or 
receiving data. 

P1-P16 
in-use 
LEDs 

Green 

Serial port is opened by server side 
software. 

Off 

Serial port is not opened by server side 
software. 

Alarm 

Red 

The relay Dout is open (exception) 

Off 

The relay Dout is Shorted (normal) 

Module 

Green 

Network module is plugged in and detected 

Off 

No module present 

GSM 

Green 

GSM Connection 

GPRS 

Orange  GPRS Connection 

GPRS/GSM 
Signal 
Strength 

Green 

More LEDs indicates better signal; 4 LEDs 
indicates maximum signal strength. 

Reviews: