Moxa Technologies AirWorks AWK-3131A User Manual Download Page 9 | Manualshive

Page: 9 / 109

background image

AirWorks AWK-3131A

Introduction

1-5

Beeper

The beeper emits two short beeps when the system is ready.

Reset Button

The RESET button is located on the top panel of the AWK-3131A. You can reboot the AWK-3131A or reset it
to factory default settings by pressing the RESET button with a pointed object such as an unfolded paper
clip.

•

System reboot: Hold the RESET button down for under 5 seconds and then release.

•

Reset to factory default: Hold the RESET button down for

over

5 seconds until the STATE LED starts

blinking green. Release the button to reset the AWK-3131A.

Relay (Digital Output)

The AWK-3131A has one relay output consisting of the 2 terminal block contacts on the top panel, as shown
below. These relay contacts are used to forward system failures and user-configured events.

The two wires attached to the relay contacts form an open circuit when a user-configured event is triggered.
If a user-configured event does not occur, the relay circuit will remain closed. For safety reasons, the relay
circuit is kept open when the AWK-3131A is not powered up.

Summary of the AWK-3131A’s Relay Status

Power Status Event

Relay

Off

–

Open

On

Yes

Open

No

Short

«
...
7
8
9
10
11
...
»

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments

Related manuals for AirWorks AWK-3131A

Brand: Acer Pages: 11

Brand: Acer Pages: 2

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 20

Brand: 3idee Pages: 4

Brand: 3idee Pages: 7

2870W - annexe 1

Brand: SMC Networks Pages: 77

DSI-LVDT Series

Brand: DEWESOFT Pages: 26

Brand: National Instruments Pages: 119

Brand: StarTech.com Pages: 2

Tesla to J1772 Adapter

Brand: Lectron Pages: 2

Brand: Kraun Pages: 32

Brand: Dynex Pages: 11

Sabrent USB-DSC8

Brand: Hitachi Pages: 21

Brand: Hitachi Pages: 4

Brand: Hitachi Pages: 28

Brand: Hitachi Pages: 76

Brand: Hitachi Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands