Moxa Technologies AirWorks AWK-3131A User Manual Download Page 105 | Manualshive

Page: 105 / 109

background image

AirWorks AWK-3131A

References

A-4

RTS Threshold

RTS Threshold (256-2346) – This setting determines how large a packet can be before the Access Point
coordinates transmission and reception to ensure efficient communication. This value should remain at its
default setting of 2,346. When you encounter inconsistent data flow, only minor modifications are
recommended.

STP and RSTP

The STP/RSTP Concept

Spanning Tree Protocol (STP) was designed to help reduce link failures in a network, and provide
protection from loops. Networks that have a complicated architecture are prone to broadcast storms caused
by unintended loops in the network. The STP protocol is part of the IEEE 802.1D standard, 1998 Edition
bridge specification.

Rapid Spanning Tree Protocol

(RSTP) implements the Spanning Tree Algorithm and Protocol defined by IEEE

802.1w-2001 standard. RSTP provides the following benefits:

•

The topology of a bridged network will be determined much more quickly compared to STP.

•

RSTP is backward compatible with STP, making it relatively easy to deploy. For example:



Defaults to sending 802.1D-style BPDUs if packets with this format are received.



STP (802.1D) and RSTP (802.1w) can operate on the LAN ports and WLAN ports (AP and WDS1-
WDS8) of the same AWK-3131A.

This feature is particularly helpful when the AWK-3131A connects to older equipment, such as legacy
switches.

Differences between RSTP and STP

RSTP is similar to STP, but includes additional information in the BPDUs that allow each bridge to confirm
that it has taken action to prevent loops from forming when it decides to enable a link to a neighboring
bridge. Adjacent bridges connected via point-to-point links will be able to enable a link without waiting to
ensure that all other bridges in the network have had time to react to the change. The main benefit of RSTP
is that the configuration decision is made locally rather than network-wide, allowing RSTP to carry out
automatic configuration and restore a link faster than STP.

«
...
103
104
105
106
107
...
»

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments

Related manuals for AirWorks AWK-3131A

Brand: StarTech.com Pages: 13

Houseport USB Z-Wave WDUSB-10MAC

Brand: Wayne-Dalton Pages: 38

Brand: Hama Pages: 53

Brand: WeGoodSun Pages: 8

Brand: J5create Pages: 2

Brand: Omicron Pages: 12

Brand: SMC Networks Pages: 2

Wireless LAN Game Adapter W11

Brand: Hama Pages: 4

Brand: Xylem Pages: 16

Brand: MSI Pages: 53

Brand: RCA Pages: 2

Brand: Kathrein Pages: 2

Brand: LEGRAND Pages: 2

Brand: Konyks Pages: 8

EasyCoder 501 E

Brand: Intermec Pages: 151

Brand: GridConnect Pages: 63

Brand: Plantronics Pages: 2

SFPCI -VME SERIES

Brand: Solflower Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands