Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download | Manualshive

Page: 92 / 94

background image

B-6

AWK-3131A-M12-RCC

Supporting Information

DoC (Declaration of Conformity)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.

RF exposure warning

This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter, End-users and
installers must be provide with antenna installation instructions and transmitter. End-users and installers
must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance.

Antenna List

Antenna Part No.

Antenna Type

Maximum Antenna Gain

ANT-WDB-WDB-O-2-BK

Dipole Antenna

2.34 dBi for 5.25~5.35GHz
2.34 dBi for 5.47~5.725GHz

ANT-WDB-ARM-0202

Dipole Antenna

1.6 dBi for 5.25~5.35 GHz
1.8 dBi for 5.47~5.725 GHz

«
...
90
91
92
93
94
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

Brand: Hawking Pages: 2

Brand: Gbord Pages: 8

Brand: East Coast Datacom Pages: 19

Brand: Cameo Pages: 23

Brand: Wave Wireless Networking Pages: 167

Brand: Neousys Technology Pages: 24

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Handicare Pages: 60

Brand: Zalip Pages: 76

Brand: ATTO Technology Pages: 2

Brand: Intel Pages: 20

Brand: ADLINK Technology Pages: 86

Brand: Lucent Technologies Pages: 7

BPN-SAS3-116A-N10

Brand: Supermicro Pages: 8

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands