Moxa Technologies Airworks AWK-3131A-M12-RCC User Manual Download Page 9 | Manualshive

Page: 9 / 94

background image

AWK-3131A-M12-RCC

Introduction

1-10

LED

Color

State

Description

WLAN

Amber

Amber On

WLAN is in AP/Master mode
WLAN is in Client/Slave/ACC Master/ACC Slave mode with
connection established

Amber/Blinking

Traffic in AP/Client/Master/Slave/ACC mode.

Off

WLAN is in Sniffer mode.
WLAN is in Client/Slave/ACC Master/ACC Slave mode without
a connection being established or WLAN is not working
properly.

LAN

Green

Green

LAN port’s 10/100/1000 Mbps link is active.

Green/Blinking

Data traffic at the LAN port.

Green Off

LAN port is disconnected.

Beeper

The beeper emits two short beeps when the system is ready.

Reset Button

The RESET button is located on the top panel of the AWK-3131A-M12-RCC. You can reboot the
AWK-3131A-M12-RCC or reset it to factory default settings by pressing the RESET button with a pointed object
such as an unfolded paper clip.

•

System reboot: Hold the RESET button down for under 5 seconds and then release it.

•

Reset to factory default: Hold the RESET button down for over 5 seconds until the STATE LED starts
blinking green. Release the button to reset the AWK-3131A-M12-RCC.

ATTENTION

When the system fails to boot, the LEDs for STATE (Green), FAULT, and WLAN will all light up
simultaneously and blink at one-second intervals. This may be due to improper operation or other issues,
such as an unexpected shutdown while updating the firmware. To recover the firmware, refer to the Firmware
Recovery section in Appendix B Supporting Information.

«
...
7
8
9
10
11
...
»

Summary of Contents for Airworks AWK-3131A-M12-RCC































































































Reviews:

No comments

Related manuals for Airworks AWK-3131A-M12-RCC

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

Brand: NAIM Pages: 2

Brand: National Instruments Pages: 17

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 23

Brand: Ubiquiti Pages: 40

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: Falcon Pages: 24

Brand: Commell Pages: 9

Brand: Accom Pages: 15

Brand: 3Com Pages: 50

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

Brand: IBASE Technology Pages: 39

Brand: Lanner Pages: 38

Brand: Allied Telesis Pages: 34

Brand: FOR-A Pages: 2

Brand: PADAUK Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands