122106R11/ MFH-F30 & DF30
CONFIGURING AND TESTING FEEDER
SET TIME OF DAY:
Press the UP or DOWN button until the
correct time of day appears. Press and release button to single-step
through the minutes or hold down to advance quickly. The feeder
will not run while buttons are being pressed and waits 10 seconds
from the last button press before it is activated. The feeder is
activated when the display alternates between the CURRENT TIME
and %BATTERY.
SET FEED TIMES:
Press the SET button until the correct Timer
Number appears in the upper right hand corner as shown. Press the
UP or DOWN button to set the Feed Time.
TEST FEEDER:
PRESS AND HOLD the SET button while the
RUN-TIME SECONDS are displayed. Release the button and get
away from the feeder when the message “TESTING GET AWAY”
appears on the display.
SET
UP
DOWN
SET
UP
DOWN
SET
UP
DOWN
SET
UP
DOWN
Your Pro Feeder will feed up to six times per day and has been factory set to feed at 7:00am and
6:00pm for four seconds. To change the factory settings or add additional feed times, follow the
instructions below. The Battery Level is displayed every seven seconds. It is recommended that the
battery be replaced when the %BATTERY reading is 25% or below.
8:00
SET TIMER
3
AM
:06
SET TIMER
3
RUN-TIME
SECONDS
:05
TESTING GET AWAY
RUN TIME (sec.)
Approx. Fish Food dispensed
4 6
8 10 12 14 16 18
2.5 2.7 2.9 3.1 3.3 3.4 3.6 3.8
ENABLE/DISABLE REMOTE:
Disabling the Wireless Remote
Control feature will increase battery life. “RF ON” indicates that the
Wireless Remote Control feature is on. To toggle between Remote
Control On and Off, simultaneously press and hold the SET and
DOWN buttons while monitoring the display.
Your Pro Feeder includes self diagnostics which automatically detect and display operational errors. If
the words “Check Door” appears on the display, there may be an obstacle interfering with the internal
dispensing mechanism or prohibiting the Feed Door from fully opening. Carefully inspect the internal
funnel and door for any obstacles that may be prohibiting it from operating properly.
TROUBLESHOOTING
SET RUN DURATION:
Press the SET button again to set the
RUN-TIME SECONDS which can range from zero to twenty
seconds. Adjust RUN-TIME SECONDS using the chart below. Set
the RUN-TIME SECONDS to zero to disable the specific timer.
CHARGING AND INSTALLING BATTERY
INSTALLING:
Place the 6V 12aH battery inside the provided Battery Sling. Connect the Black
Wire to the Negative Terminal (-) and the Red Wire to the Positive Terminal (+). Lower battery into
Control Box and Close Lid. If a low battery can be swapped with a fresh battery within 10 seconds,
the clock and timer settings will be retained. If the battery cannot be swapped within 10 seconds,
leave the battery disconnected for at least 60 seconds so that the system can reset properly.
20
4.0
CHARGING:
Remove the battery from the Feeder. Connect the provided Battery Charger’s Black
Wire to the Negative Battery Terminal (-) and Red Wire to the Positive Battery Terminal (+) . Plug
the battery charger into a 120VAC electrical outlet. When the green light blinks on the charger, the
battery is fully charged. A fully discharged battery may require up to 24 hours of charging. Do not
leave the battery connected to the charger for more than 24 hours.
Our Service Department will gladly answer any questions you have. Call
205-664-6700 or 800-653-3334, Monday - Friday, 8:00 AM to 5:00 PM CST.
www.moultriefeeders.com
Approx. Corn dispensed (lbs.)
1.9 2.2 2.5 2.7 3.0 3.3 3.6 3.8 4.1
NOTE: This equipment has been tested and found to comply with the limits of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
ENABLE/DISABLE DOOR:
The feed door could freeze shut under extreme weather conditions.
To lock the door in an open position, but allow the feeder to operate as normal, the door may be
disabled. To toggle between Door Enable and Disable, simultaneously press and hold the SET and
UP buttons.
SET
UP
DOWN
SET
UP
DOWN
