Motorola VX-P949 User Manual Download | Manualshive

Page: 89 / 112

background image

Mode

Description

Transmit Inhibit on Busy Channel with Wrong
Squelch Code

You cannot transmit on an active channel with a
squelch code or (if secure-equipped) encryption
key other than your own. If the PL code is the
same as yours, the transmission is not prevent-
ed.

Quick-Key Override

Your radio must be preprogrammed to allow
you to use Quick-Key Override. This feature
works with either one of the two above varia-
tions. You can override the transmit-inhibit state
by quick-keying the radio (press

PTT

button

twice within the preprogrammed time limit).

6.16.17

Transmit Inhibit

This feature allows you to stops all transmission including voice and data. The radio can receive
messages but not able to reply the acknowledgment request of the received message.

This feature is available for Conventional operations for all VX-P radios.

You can physically control the transmission of the radio especially during operation in hazardous
environments. An environment is considered hazardous if radio transmission could initiate an explosion
or other dangerous reactions.

6.16.17.1

Enabling Transmit Inhibition

Procedure:

Perform one of the following actions:

• Switch the preprogrammed Transmit Inhibit switch to Transmit Inhibit enabled.

•

or to

TxIn

. Press the

Menu Select

button below

TxIn

.

• Press the

Transmit Inhibit

programmable button.

The display shows

Tx inhibit on

. You hear a sequence of short, low-high tones to indicate

that transmission is inhibited.

Pressing

PTT

triggers the radio sounds a constant short, low-pitched tone (reject tone).

NOTICE:

The status of the Transmit Inhibit does not change after the radio powers up.

6.16.17.2

Disabling Transmit Inhibition

Procedure:

Perform one of the following actions:

• Switch the preprogrammed Transmit Inhibit switch to Transmit Inhibit disabled position.

•

or to

TxIn

. Press the

Menu Select

button below

TxIn

.

• Press the Transmit Inhibit programmable button.

MN003602A01-AF

Advanced Features

89

«
...
87
88
89
90
91
...
»

Summary of Contents for VX-P949

















































































































Reviews:

No comments

Related manuals for VX-P949

Brand: Pure Digital Pages: 18

DUAL-VOX LTR-01

Brand: B&G electronics Pages: 5

Brand: RACEceiver Pages: 2

Brand: SimonsVoss Pages: 16

Brand: Hytera Pages: 27

freecomm 150 PMR 446

Brand: stabo Pages: 20

MICROTALK CX105

Brand: Cobra Pages: 1

Brand: Cobra Pages: 19

Brand: Garmin Pages: 8

Brand: Hitachi Pages: 20

Brand: Vertex Standard Pages: 40

Brand: Motorola Pages: 29

Brand: Naxa Pages: 11

Brand: Navman Pages: 18

Brand: TEXAS RANGER Pages: 29

Brand: DigiTech Pages: 8

Brand: Uniden Pages: 2

Brand: Radionette Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands