Motorola VX-P949 User Manual Download

Page: 87 / 112

6.16.12

Adjusting Squelch Level

The Adjustable Fine Tune Squelch feature allows you to adjust the desired squelch level of the radio
between level 0 and 15.

The following settings determine the types of call that you receive:

• 0 – Squelch is open and all calls regardless of signal strength and background noise pass through

• Lower setting – Calls with low signal strength and higher than normal background noise pass

through

• Higher Setting – Calls with low signal strength and higher than normal background noise are filtered

out

Procedure:

From the

Home

screen, press and hold the preprogrammed

Private Line Disable

button.

The radio displays the

Squelch

menu.

To adjust the squelch level, perform one of the following actions:

• Press

• Press the

Left

Right

navigation key.

To return to the

Home

screen, press the

Home

button.

6.16.13

Conventional Squelch Operation

This feature filters out unwanted calls with low signal strength or channels that have a higher than
normal background noise.

Analog Options

Tone Private Line, Digital Private-Line, and carrier squelch is available (preprogrammed) per channel.

Option

Result

Carrier squelch

You hear all traffic on a channel.

Tone Private Line or Digital Private-Line

The radio responds only to your messages.

Digital Options

One or more of the following options may be preprogrammed in your radio. Contact your system
administrator for more information.

Option

Result

Digital Carrier-Operated Squelch

You hear all digital traffic.

Normal Squelch

You hear any digital traffic having the correct
network access code.

Selective Switch

You hear any digital traffic having the correct
network access code and correct talkgroup.

MN003602A01-AF

Advanced Features

Summary of Contents for VX-P949
















































































































Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands

Motorola VX-P949, User Manual

Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands