Motorola VX-P949 User Manual Download

Page: 58 / 112

The microphone remains active for the hot mic time specified in your radio's codeplug
programming.

To exit Emergency Call, press and hold the preprogrammed

Emergency

button.

Turning off the radio also cancels the emergency state.

6.7.8

Sending a Silent Emergency Alarm

When and where to use:

This feature allows you to send an Emergency Alarm to the system without

triggering any audio or visual indicators.

Procedure:

Press the preprogrammed

Emergency

button.

The display shows no changes, the LED does not light up, and you hear no tones. The silent
emergency state continues until you perform the next step.

Perform one of the following actions:

• Press and hold the preprogrammed

Emergency

button for about a second to exit the Silent

Emergency Alarm mode.

• Press and release the

PTT

button to exit the Silent Emergency Alarm mode and enter regular

dispatch or Emergency Call mode.

6.8

Fireground

The portable Fireground Communications System is designed for deployment at an incident scene.

It consists of central components that provide on-scene and inbuilding radio coverage, and enhanced
personnel accountability and monitoring:

• Incident Management Software

• Command Terminal

• Radio Frequency (RF) Modem (Conventional Only)

• DVRS (Optional)

If you have a critical situation, you can press the Emergency button which activates an alarm on the
Incident Management Software at the command terminal.

The command terminal receives the following status updates from your radio:

• Turning the radio on and off

• Automatic response to Polling

• Response to Evacuation commands

• Pressing the

PTT

button to make voice transmission

• Sending an Emergency Alarm and Call

6.8.1

Entering Fireground Zone Channel (Conventional)

Procedure:

Upon powering up, one of the following scenarios occurs:

MN003602A01-AF
Advanced Features

Summary of Contents for VX-P949
















































































































Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands

Motorola VX-P949, User Manual

Search results

Summary of Contents for VX-P949

Reviews:

Related manuals for VX-P949

Brands by name

Popular brands