manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

Share
Download
Motorola Symbol DS3407 Reference Manual Download Page 69

Imaging Preferences

5 - 9

Image Capture Autoexposure

Parameter # F0h, 68h

Select 

Enable Image Capture Autoexposure

 to allow the digital scanner to control gain settings and exposure 

(integration) time to best capture an image for the selected operation mode.

Select 

Disable

 

Image Capture Autoexposure

 to manually adjust the gain and exposure time (see the following 

pages). This option is only recommended for advanced users with difficult image capture situations.

Image Capture Illumination

Parameter # F0h, 69h

Selecting 

Enable Image Capture Illumination

 causes the digital scanner to flash on every image capture. Select 

Disable

 

Image Capture Illumination

 to prevent the digital scanner from using artificial illumination.

Enabling illumination usually results in superior images. The effectiveness of the illumination decreases as the 
distance to the target increases. 

*Enable Image Capture Autoexposure

(01h)

Disable Image Capture Autoexposure

(00h)

*Enable Image Capture Illumination

(01h)

Disable Image Capture Illumination

(00h)

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands