manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

Share
Download
Motorola Symbol DS3407 Reference Manual Download Page 186

10 - 38 Symbol DS3407 Product Reference Guide

Code 11

Code 11

Parameter # 0Ah

To enable or disable Code 11, scan the appropriate bar code below. 

Set Lengths for Code 11

Parameter # L1 = 1Ch, L2 = 1Dh

The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) 
the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specific 
range.

•

One Discrete Length 

- Select this option to decode only Code 11 symbols containing a selected length. 

Select the length using the numeric bar codes in 

Appendix D, Numeric Bar Codes

. For example, to decode 

only Code 11 symbols with 14 characters, scan 

Code 11 - One Discrete Length

, then scan 

1 

followed by

 4

. 

To correct an error or to change the selection, scan 

Cancel

 on 

page D-3

.

•

Two Discrete Lengths

 - Select this option to decode only Code 11 symbols containing either of two 

selected lengths. Select lengths using the numeric bar codes in 

Appendix D, Numeric Bar Codes

. For 

example, to decode only Code 11 symbols containing either 2 or 14 characters, select 

Code 11 - Two 

Discrete Lengths

, then scan 

0

, 

2

,

 1

, and then 

4

. To correct an error or to change the selection, scan 

Cancel

 on 

page D-3

.

•

Length Within Range

 - Select this option to decode a Code 11 symbol with a specific length range. 

Select lengths using numeric bar codes in 

Appendix D, Numeric Bar Codes

. 

For example, to decode 

Code 11 symbols containing between 4 and 12 characters, first scan 

Code 11 - Length Within Range

. 

Then scan 

0

, 

4

, 

1,

 and 

2

 (enter a leading zero for single digit numbers). To correct an error or change the 

selection, scan 

Cancel

 on 

page D-3

.

•

Any Length

 - Scan this option to decode Code 11 symbols containing any number of characters within the 

digital scanner’s capability. 

Enable Code 11

(01h)

*

Disable Code 11

(00h)

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands