Motorola Symbol DS3407 Reference Manual Download Page 168

Page: 168 / 404

10 - 20 Symbol DS3407 Product Reference Guide

Bookland ISBN Format

Parameter # F1h 40h

If you enabled Bookland EAN using

Enable/Disable Bookland EAN on page 10-9

, select one of the following

formats for Bookland data:

•

Bookland ISBN-10

- The scanner reports Bookland data starting with 978 in traditional 10-digit format with

the special Bookland check digit for backward-compatibility. Data starting with 979 is not considered
Bookland in this mode.

•

Bookland ISBN-13

- The scanner reports Bookland data (starting with either 978 or 979) as EAN-13 in

13-digit format to meet the 2007 ISBN-13 protocol.

*Bookland ISBN-10

(00h)

Bookland ISBN-13

(01h)

NOTE

For Bookland EAN to function properly, first enable Bookland EAN using

Enable/Disable Bookland EAN

on page 10-9

, then select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/EAN

Supplementals, or Enable 978/979 Supplemental Mode in

Decode UPC/EAN/JAN Supplementals on

page 10-10

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Search results

Summary of Contents for Symbol DS3407

Reviews:

Brands by name

Popular brands

Motorola Symbol DS3407, Reference Manual

Search results

Summary of Contents for Symbol DS3407

Reviews:

Brands by name

Popular brands