manualshive.com logo in svg

Motorola MTX series, Programmer'S Reference Manual, Page: 93 / 223

Share
Download
Motorola MTX series Programmer'S Reference Manual Download Page 93

2-40

Computer Group Literature Center Web Site

Raven PCI Host Bridge & Multi-Processor Interrupt Controller

2

DPAR  Data Parity Detected. This bit is set when three conditions are 
met: 1) the Raven asserted PERR* itself or observed PERR* asserted; 2) 
the Raven was the PCI master for the transfer in which the error occurred; 
3) the PERR bit in the PCI Command Register is set. This bit is cleared by 
writing it to 1; writing a 0 has no effect.

SELTIM  DEVSEL Timing. This field indicates that the Raven will 
always assert DEVSEL* as a ‘medium’ responder.

SIGTA  Signalled Target Abort. This bit is set by the PCI slave 
whenever it terminates a transaction with a target-abort. It is cleared by 
writing it to 1; writing a 0 has no effect.

RCVTA  Received Target Abort. This bit is set by the PCI master 
whenever its transaction is terminated by a target-abort. It is cleared by 
writing it to 1; writing a 0 has no effect.

RCVMA  Received Master Abort. This bit is set by the PCI master 
whenever its transaction (except for Special Cycles) is terminated by a 
master-abort. It is cleared by writing it to 1; writing a 0 has no effect.

SIGSE  Signaled System Error. This bit is set whenever the Raven 
asserts SERR*. It is cleared by writing it to 1; writing a 0 has no effect.

RCVPE  Detected Parity Error. This bit is set whenever the Raven 
detects a parity error, even if parity error checking is disabled (see bit 
PERR in the PCI Command Register). It is cleared by writing it to 1; 
writing a 0 has no effect.

Revision ID/ Class Code Registers

REVID  Revision ID. This register identifies the Raven revision level. 
This register is duplicated in the PPC Registers.

Offset

$08

Bit

3
1

3
0

2
9

2
8

2
7

2
6

2
5

2
4

2
3

2
2

2
1

2
0

1
9

1
8

1
7

1
6

1
5

1
4

1
3

1
2

1
1

1
0 9 8 7 6 5 4 3 2 1 0

Name

CLASS

REVID

Operation

R

R

Reset

$060000

$03

Summary of Contents for MTX series
































































































































































































































Reviews:

No comments