manualshive.com logo in svg

Motorola MTX series, Programmer'S Reference Manual

The Motorola MTX series Programmer's Reference Manual is a comprehensive resource to unlock the full potential of your device. Browse our website to access and download this invaluable manual, completely free of charge. Discover step-by-step instructions and tips from the experts, enhancing your user experience. Only at manualshive.com.

Share
Download
background image

2-76

Computer Group Literature Center Web Site

Raven PCI Host Bridge & Multi-Processor Interrupt Controller

2

memory. If interrupts from ISA devices are directly connected to the 
Raven MPIC (bypassing the 8259), the device driver interrupt 
service routine must read status from the ISA device to ensure 
buffers between the device and system memory are flushed.

Reset State

After a power-on reset the Raven MPIC state is:

❏

Current task priority for all CPUs set to 15.

❏

All interrupt source priorities set to zero.

❏

All interrupt source mask bits set to a one.

❏

All interrupt source activity bits cleared.

❏

Processor Init Register is cleared.

❏

All counters stopped and interrupts disabled.

❏

Controller mode set to 8259 pass-through.

Operation

Interprocessor Interrupts

Four interprocessor interrupt (IPI) channels are provided for use by all 
processors. During system initialization the IPI vector/priority registers for 
each channel should be programmed to set the priority and vector returned 
for each IPI event. During system operation a processor may generate an 
IPI by writing a destination mask to one of the IPI dispatch registers. 

Note that each IPI dispatch register is shared by both processors. Each IPI 
dispatch register has two addresses but they are shared by both processors. 
That is, there is a total of four IPI dispatch registers in the Raven MPIC.

The IPI mechanism may be used for self interrupts by programming the 
dispatch register with the bit mask for the originating processor. 

Summary of Contents for MTX series
































































































































































































































Reviews:

No comments

Related manuals for MTX series

ST STM32746G-EVAL User Manual preview
STM32746G-EVAL
Brand: ST Pages: 79
Texas Instruments TPA2005D1 User Manual preview
TPA2005D1
Brand: Texas Instruments Pages: 22
AOpen MX46L Easy Installation Manual preview
MX46L
Brand: AOpen Pages: 8
Sure Electronics Wondom ICP3 User Manual preview
Wondom ICP3
Brand: Sure Electronics Pages: 32
C&T Solution CT-DBX0x User Manual preview
CT-DBX0x
Brand: C&T Solution Pages: 65
IWILL P4SE2 User Manual preview
P4SE2
Brand: IWILL Pages: 48
ZMDI ZSSC5101 Manual preview
ZSSC5101
Brand: ZMDI Pages: 25
Honda Outboard Motor BF5A Owner'S Manual preview
Outboard Motor BF5A
Brand: Honda Pages: 84
Aaeon SBC-770 User Manual preview
SBC-770
Brand: Aaeon Pages: 111
Memec Virtex-4 User Manual preview
Virtex-4
Brand: Memec Pages: 45
Gigabyte GA-IMB1900N User Manual preview
GA-IMB1900N
Brand: Gigabyte Pages: 38
Gigabyte GA-K8NSNXP User Manual preview
GA-K8NSNXP
Brand: Gigabyte Pages: 96
Supermicro H8QG7-LN4F User Manual preview
H8QG7-LN4F
Brand: Supermicro Pages: 84
ST EVALSP820-XS User Manual preview
EVALSP820-XS
Brand: ST Pages: 11
Gigabyte GA-6OXC User Manual preview
GA-6OXC
Brand: Gigabyte Pages: 113
Zotac D2550ITX Series User Manual preview
D2550ITX Series
Brand: Zotac Pages: 50
TYAN S2735 Manual preview
S2735
Brand: TYAN Pages: 86
Asus Motherboard PR-DLS533 User Manual preview
Motherboard PR-DLS533
Brand: Asus Pages: 142

Brands by name

Popular brands

Load more brands