background image

29 

Appendix C:  FCC Information 

 
CAUTION: Changes or modifications made in the CPU box or Display, not expressly 
approved by Motorola, will void the user's authority to operate the equipment 
 
EPS – 48759 – O 

 

 

 

         FCC INTERFERENCE WARNING 

The  FCC  requires  that  manuals  pertaining  to  Class  A  and  Class  B  computing  devices 
must  contain  warnings  about  possible  interference  with  local  residential  radio  and  TV 
reception. This warning reads as follows: 
NOTE:  This  equipment  has  been  tested  and  found  to  comply  with  limits  for  a  Class  B 
digital device, pursuant to Part 90 of the FCC Rules. These limits are designed to provide 
reasonable  protection  against  harmful  interference  when  the  equipment  is  operated  in  a 
commercial or  residential  environment.  This  equipment generates, uses, and  can  radiate 
radio  frequency energy and, if  not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. 
For  detailed  product  safety  and  RF  exposure  for  mobile  stations  with  two-way  radios 
installed  in  vehicles,  refer  to  Electromagnetic  Emission  (EME)  safety  leaflet,  Motorola 
publication number 68P02967C16. 
 
 
FCC Compliance Notice 
The FCC requires that manuals pertaining to Class A and Class B computing devices 
must contain warnings about possible interference with local residential radio and TV 
reception. This warning reads as follows: 
 
NOTE: This equipment has been tested and found to comply with limits for a Class B 
digital device, pursuant to Part 90 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial or residential environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. 
This device complies with Part 90 of the FCC Rules. Operation is subject to the following 
two conditions:  
 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that may 
cause undesired operation. 
 
For detailed product safety and RF exposure for mobile workstations, with two-way 
radios, installed in vehicles, refer to Electromagnetic Emission (EME) safety leaflet, 
Motorola publication number 68P02967C16. 
 

 

Summary of Contents for Mobile Workstation 800 Series


































Reviews: