Motorola MC92603 Reference Manual Download | Manualshive

Page: 69 / 134

background image

MOTOROLA

Chapter 4. Management Interface (MDIO)

4-5

MDIO Registers

4.2.3

MDIO RA 2 and 3—PHY Identifier Registers

Figure 4-2 shows the format for the PHY identifier registers in the MC92603. MDIO RAs
2 and 3 are read-only and contain a 32-bit pattern that uniquely identifies the MC92603.
They provide bits 3–24 of Motorola’s ‘organizational unique identifier’ (0x000A28), the 6
least significant bits (lsb) of the part number and the revision level for the MC92603.

4

Remote fault

Bit 4 is initialized to zero and is set when the receiver detects a remote fault. (R, LH, SC)

3

Auto-negotiation
ability

Bit 3 reports the AN ability per register 0.12. It may be changed via register 0.12 through
the MDIO interface. (R)

2

Link status

Bit 2 is initialized to zero. It reflects whether the receiver has achieved byte
synchronization. (R)

1

Jabber detect

Bit 1 is forced to zero and may not be modified. (R)

0

Extended capability

Bit 0 is forced to one and may not be modified. The MC92603 has a specific status and
configuration register (register 17) for each channel. (R)

1

R = read only, LH = latches high, and SC = self-cleaning.

Register

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

2

R

Bits 03–18 of OUI

W

Reset

0

1

0

1

0

0

0

1

0

1

0

0

0

0

0

0

Register

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

3

R

Bits 19–24 of OUI

Manufacturer’s Model #

Revision

W

Reset

0

0

0

0

0

0

0

0

0

0

1

1

0

0

0

0

Figure 4-3. PHY Identifier Registers (MDIO RA 2 and 3)

Table 4-3. Status Register (MDIO RA 1) Field Descriptions (continued)

Bits

Name

Description

1

«
...
67
68
69
70
71
...
»

Summary of Contents for MC92603







































































































































Reviews:

No comments

Related manuals for MC92603

Brand: 3Com Pages: 48

Brand: Draytek Pages: 8

Brand: ZyXEL Communications Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 184

Brand: E-TOP Pages: 24

Brand: Intellinet Pages: 12

Brand: IBASE Technology Pages: 39

Brand: BinTec Pages: 34

Brand: Valcom Pages: 4

Brand: Enterasys Pages: 62

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

Brand: Garderos Pages: 21

Brand: Premio Pages: 2

MSR-20-21 ROUTER

Brand: H3C Pages: 83

Brand: N-Tron Pages: 2

Brand: Tenda Pages: 74

Bipac 74 Series

Brand: Billion Pages: 8

Transport WR41-C

Brand: Digi Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands