manualshive.com logo in svg

Motorola M-CORE MMC2001 Series, Reference Manual

The Motorola M-CORE MMC2001 Series Reference Manual is the ultimate guide to unlocking the full potential of your device. This comprehensive manual provides step-by-step instructions and valuable tips to ensure optimal performance. Download this manual for free from our website today to maximize your Motorola experience.

Share
Download
background image

MMC2001

INTEGER CPU

MOTOROLA 

REFERENCE MANUAL

2-13 

Figure 2-6 External Multiplexer Connections

Table 2-3 lists the combinations of the TSIZx, ADDR1, and ADDR0 signals that are
used for each possible transfer size and alignment. In Table 2-3, MB0–MB3 indicate
the portion of the requested operand that is read or written during that bus transfer.
For word transfers, all bytes are valid as listed and correspond to portions of the
requested operand. The bytes labeled with a dash are not required; they are ignored
on read transfers and driven with undefined data on write transfers. 

2.8.5 Processor Instruction/Data Transfers

The transfer of data between the processor and other devices involves the address
bus, data bus, transfer attributes, and control signals. The address and data buses
are parallel, non-multiplexed buses that support aligned byte, halfword, and word
transfers. All bus input and output signals are sampled or driven with respect to one of
the edges of the CLK signal. The M•CORE moves data on the bus by issuing control
signals and using a handshake protocol to ensure correct data movement.

Access requests are generated in an overlapped fashion in order to support sus-
tained single-cycle transfers. Once an access has been accepted, the processor is
free to change the current request. Access information must therefore be latched by a
slave device.

M•CORE

DATA[31:24]

DATA[23:16]

DATA[15:8]

DATA[7:0]

MB0

MB1

MB2

MB3

MEMORY

PORT

Multiplexer

Structure

(byte addr
0,4,8,C,...)

(byte addr
3,7,B,F,...)

(byte addr
2,6,A,E,...)

(byte addr
1,5,9,D,...)

g

g

b,

 e

a

e

c

f, g

d, f, g

Connection Cases

 

   

  

Freescale Semiconductor,

 I

                                               

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

nc.

..

Summary of Contents for M-CORE MMC2001 Series




































































































































































































































































Reviews:

No comments

Related manuals for M-CORE MMC2001 Series

ABB ACS355 series Quick Start Up Manual preview
ACS355 series
Brand: ABB Pages: 139
ABB ACH400 Series Retrofit Manual preview
ACH400 Series
Brand: ABB Pages: 28
ABB TZIDC-110 Operating Instructions Manual preview
TZIDC-110
Brand: ABB Pages: 59
Wasp B2000 Installation Manual preview
B2000
Brand: Wasp Pages: 16
Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
Nabco Opus Control Installation Manual preview
Opus Control
Brand: Nabco Pages: 35
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Brand: Parker Pages: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Brand: Parker Pages: 26
Vageo DT-1 Manual preview
DT-1
Brand: Vageo Pages: 2
Linear Technology LT8570 Demo Manual preview
LT8570
Brand: Linear Technology Pages: 7
YASKAWA J1000 CIMR-JC series Installation Manual preview
J1000 CIMR-JC series
Brand: YASKAWA Pages: 25
Netafim AlphaDisc BLE Quick Manual preview
AlphaDisc BLE
Brand: Netafim Pages: 4
TREND IQ422 Installation Instructions Manual preview
IQ422
Brand: TREND Pages: 12
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Instrutech VGC301 User Manual preview
VGC301
Brand: Instrutech Pages: 42
PXM DMX DEMUX 8 Manual preview
DMX DEMUX 8
Brand: PXM Pages: 15
wattstopper LMRC-111 Quick Start Manual preview
LMRC-111
Brand: wattstopper Pages: 4

Brands by name

Popular brands

Load more brands