Contents
Overview
Installation
1
2
3
4
Precautions
■
If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself. (We
shall not be responsible for any problems caused by unauthorized repair or
maintenance.)
■
Do not allow water or liquid intrusion into the camera.
■
In the use of the product, you must be strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on wall
or ceiling, the device shall be firmly fixed.
■
Do not use camera beyond specified voltage range.
■
Do not drop the camera or subject it to physical shock.
■
Avoid touching the camera lens.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
■
Do not aim the camera at the sun or extra bright place.
■
Do not place the camera in extremely hot, cold (the operating temperature
shall be -30˚C~60˚C), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
IP Varifocal Camera
Quick Start Guide
Camera
Quick
start
guide
CD
Plastic
plug
×4
Drill
template
Rubber plug
Screwdriver
4 tapping screws PA 4×25
CVBS&DC
IN cables
①
Loosen
the
nut
from
the
main
element (security cap).
②
Run
the
network
cable (without
RJ 45
connector) through the both
elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the nut
and
the
main
cover
.
■
Please read this instruction carefully before using the product and keep
it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without notice.
2
1
3
1
Ethernet
Connector
2
Audio Input (MIC)
3
Audio
Output (HP)
4
CVBS
Video Output
5
Alarm Input/Output
6
DC12V Power
Connector
7A Zoom- (only available for type A)
8A Zoom+ (only available for type A)
7B Focus
8B Zoom
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS Interface
* Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera.
* Please install the camera in the dry environment. You'd better install back the
lower dome less than 4 hours after removing it.
*
Connecting
Network
Cable
10
7A
7B
8A
8B
9
11
Lens cover
IR light hood
Type A: Motorized
zoom
camera
Type B: Manual
zoom
camera
*
If the PoE switch is used to power the camera
,
DC12V power supply is not
required.
*
It is recommended to install the security cap for outdoor installation.
①
②
Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Trim Ring
∅
4
.6
90.2mm
90.2mm
Do not remove the protection film until finishing the installation.
Rotate the trim ring anticlockwise to remove it from the camera.
Figure 1
Figure 2
1
3
4
5
6
2
A
L
A
R
M
4 3 2 1
Se
cu
ri
ty c
ap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
A
L
A
R
M
4 3 2 1
③
Loosen the screws to open the lower dome.
④
Route and connect these cables. Then secure the camera to the
ceiling or wall with the screws provided.
Hold it
and
rotate
Rubber plug
Lower dome
⑤
Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor (See Figure 5) and then adjust the camera according to
the figure below to get an optimum angle.
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
Figure 3
Figure 4
* Install it when routing the cables
through the ceiling.
