manualshive.com logo in svg

Motorola F3030A, Developer'S Manual, Page: 29 / 72

Share
Download
Motorola F3030A Developer'S Manual Download Page 29

98-08901C67-O

23

Developer Board and Interfaces Description

3.4.4

External Antenna

An antenna (internal or external) must be connected to the Developer Board for adequate GSM reception. You can connect the
g20 to either the on-board internal antenna or to an external antenna. 

Two RF connectors on the side of Developer Board, labeled INT ANT and EXT ANT on the cover, are used for setting up the
antenna.

Figure 15. Antenna Connectors (external)

On the inside of the Developer Board, the EXT ANT connector is connected to the g20 and the INT ANT is connected to the
on-board internal antenna.

You must perform one of the following:

• To use the internal antenna, connect the EXT ANT and INT ANT connectors with the additional RF cable supplied in the

Developer’s Kit.

Figure 16. Antenna Connectors (internal)

• To use an external antenna, connect an external antenna or antenna application to the EXT ANT connector. (The connection

cable is not included.)

External

Antenna Input

Internal

Antenna Input

On-board

Internal Antenna

g20 RF Cable

Additional

RF Cable

EXT ANT

INT ANT

Summary of Contents for F3030A









































































Reviews:

No comments