manualshive.com logo in svg

Motorola DSP56F803, Hardware User Manual

Share
Download
Motorola DSP56F803 Hardware User Manual Download Page 13

Introduction

1-1

Chapter 1
Introduction

The DSP56F803EVM is used to demonstrate the abilities of the DSP56F803 and to 
provide a hardware tool allowing the development of applications that use the 
DSP56F803.

The DSP56F803EVM is an evaluation module board that includes a DSP56F803 part, 
peripheral expansion connectors, external memory, RS-232 interface and a CAN 
interface.  The expansion connectors are for signal monitoring and user feature 
expandability.

 The DSP56F803EVM is designed for the following purposes:

•

Allowing new users to become familiar with the features of the 56800 architecture. 
The tools and examples provided with the DSP56F803EVM facilitate evaluation of 
the feature set and the benefits of the family.

•

Serving as a platform for real-time software development. The tool suite enables 
the user to develop and simulate routines, download the software to on-chip or 
on-board RAM, run it, and debug it using a debugger via the JTAG/OnCE

TM

 port.  

The breakpoint features of the OnCE port enable the user to easily specify complex 
break conditions and to execute user-developed software at full-speed, until the 
break conditions are satisfied.  The ability to examine and modify all user 
accessible registers, memory and peripherals through the OnCE port greatly 
facilitates the task of the developer.

•

Serving as a platform for hardware development. The hardware platform enables 
the user to connect external hardware peripherals.  The on-board peripherals can be 
disabled, providing the user with the ability to reassign any and all of the DSP's 
peripherals.  The OnCE port's unobtrusive design means that all of the memory on 
the board and on the DSP chip are available to the user.

1.1   DSP56F803EVM Architecture

The DSP56F803EVM facilitates the evaluation of various features present in the 
DSP56F803 part.  The DSP56F803EVM can be used to develop real-time software and 

Summary of Contents for DSP56F803



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands