Motorola DSP56309 User Manual Download Page 254 | Manualshive

Page: 254 / 425

background image

Triple Timer Module

Triple Timer Module Programming Model

MOTOROLA

DSP56309UM/D 9-13

The INV bit is cleared by a hardware RESET signal or a software RESET instruction.

The INV bit affects both the timer and GPIO modes. To insure correct operation, this bit
should be changed only when one or both of the following conditions is true:

¥ The timer has been disabled by clearing the TE bit in the TCSR.

¥ The timer is in GPIO mode.

The INV bit does not affect the polarity of the prescaler source when the TIO is used as
input to the prescaler.

9.3.4.6

Timer Reload Mode (TRM) Bit 9

The TRM bit controls the counter preload operation.

In timer (0Ð3) and watchdog (9Ð10) modes, the counter is preloaded with the TLR value
after the TE bit is set and the first internal or external clock signal is received. If the TRM
bit is set, the counter is reloaded each time after it reaches the value contained by the
TCR. In PWM mode (7), the counter is reloaded each time counter overflow occurs. In
measurement (4Ð5) modes, if the TRM and the TE bits are set, the counter is preloaded
with the TLR value on each appropriate edge of the input signal.

If the TRM bit is cleared, the counter operates as a free running counter and is
incremented on each incoming event. The TRM bit is cleared by a hardware RESET
signal or a software RESET instruction.

7

Ñ

Ñ

Pulse generated
by the timer has

positive

polarity

Pulse generated by
the timer has

negative

polarity

9

Ñ

Ñ

Pulse generated
by the timer has

positive

polarity

Pulse generated by
the timer has

negative

polarity

10

Ñ

Ñ

Pulse generated
by the timer has

positive

polarity.

Pulse generated by
the timer has

negative

polarity

Table 9-3

Inverter (INV) Bit Operation (Continued)

Mode

TIO Programmed as Input

TIO Programmed as Output

INV = 0

INV = 1

INV = 0

INV = 1

«
...
252
253
254
255
256
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

Brand: dbx Pages: 2

CBT-500FP - SmartPower Premier Blender/ Food Processor

Brand: Cuisinart Pages: 33

Brand: Ametek Land Pages: 60

Nexperia PNX2000

Brand: Philips Pages: 31

Digital Multi Processors WZ-DM35NH

Brand: Panasonic Pages: 1

Brand: AUDIMAX Pages: 19

Brand: Fakir Pages: 52

Brand: Cookworks Signature Pages: 7

Brand: HAMILTON BEACH/PROCTOR SILEX Pages: 13

Brand: Philips Pages: 40

Brand: Philips Pages: 3

Brand: Menuett Pages: 36

Brand: Abode Pages: 20

Brand: Kompernass Pages: 74

Brand: Kenmore Pages: 12

Brand: Seg Pages: 88

Brand: Mellerware Pages: 5

2 6 2 1 05 0 0 W

Brand: Mellerware Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands