manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

Chapter  1.  Overview

 

  

1-7

 

System Design

 

to 2 stop bits in 1/16-bit increments. Receive and transmit FIFOs minimize CPU service
calls. A wide variety of error detection and maskable interrupt capability is provided.

Using a programmable prescaler or an external source, the MCF5272 system clock
supports various baud rates. Modem support is provided with request-to-send (RTS) and
clear-to-send (CTS) lines available externally. Full-duplex autoecho loopback, local
loopback, and remote loopback modes can be selected.

The UART can be programmed to interrupt or wake-up the CPU on various normal or
abnormal events. To reduce power consumption, the UART can be disabled by software if
not in use.

 

1.2.4  Timer Module

 

The timer module contains five timers arranged in two submodules. One submodule
contains a programmable software watchdog timer. The other contains four independent,
identical general-purpose timer units, each containing a free-running 16-bit timer for use in
various modes, including capturing the timer value with an external event, counting
external events, or triggering an external signal or interrupting the CPU when the timer
reaches a set value. Each unit has an 8-bit prescaler for deriving the clock input frequency
from the system clock or external clock input. The output pin associated with each timer
has programmable modes.

To reduce power consumption, the timer module can be disabled by software.

 

1.2.5  Test Access Port

 

For system diagnostics and manufacturing testing, the MCF5272 includes user-accessible
test logic that complies with the IEEE 1149.1 standard for boundary scan testing, often
referred to as JTAG (Joint Test Action Group). The IEEE 1149.1 Standard provides more
information. 

 

1.3   System Design

 

This section presents issues to consider when designing with the MCF5272. It describes
differences between the MCF5272 (core and peripherals) and various other standard
components that are replaced by moving to an integrated device like the MCF5272.

 

1.3.1  System Bus Configuration

 

The MCF5272 has flexibility in its system bus interfacing due to the dynamic bus sizing
feature in which 32-,16-, and 8-bit data bus sizes are programmable on a per-chip select
basis. The programmable nature of the strobe signals (including OE/RD, R/W, BS[3:0], and
CS

 

n

 

) should ensure that external decode logic is minimal or nonexistent. Configuration

software is required upon power-on reset before chip-selected devices can be used, except

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Maco Standard Fitting Instructions Manual preview
Standard
Brand: Maco Pages: 38
8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Brand: Lantronix Pages: 8
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Cervoz MEC-COM-2032i User Manual preview
MEC-COM-2032i
Brand: Cervoz Pages: 22
Nvidia Quadro M6000 Sync User Manual preview
Quadro M6000 Sync
Brand: Nvidia Pages: 8
Silicon Systems SiliconDrive SSD-P16G(I)-3100 Datasheet preview
SiliconDrive SSD-P16G(I)-3100
Brand: Silicon Systems Pages: 108
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Brand: Arbor Technology Pages: 8
ETL TeleCLIENT TC7730 Series User Manual preview
TeleCLIENT TC7730 Series
Brand: ETL Pages: 83
QTech QSW-2900 User Manual preview
QSW-2900
Brand: QTech Pages: 406
Aqua Computer Aquaduct 240 eco Operating And Assembly Manual preview
Aquaduct 240 eco
Brand: Aqua Computer Pages: 20
Omron NJ501-1300 User Manual preview
NJ501-1300
Brand: Omron Pages: 432
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
Xilinx ML506 Quick Start Manual preview
ML506
Brand: Xilinx Pages: 29

Brands by name

Popular brands

Load more brands