manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

1-6

 

MCF5272 User’s Manual

 

 

 

MCF5272 Architecture  

 

A software watchdog timer is also provided for system protection. If programmed, the
timer causes a reset to the MCF5272 if it is not refreshed periodically by software.

 

1.2.2.4  Power Management

 

The sleep and stop power management modes reduce power consumption by allowing
software to shut down the core, peripherals, or the whole device during inactive periods. To
reduce power consumption further, software can individually disable internal clocks to the
on-chip peripheral modules. The power-saving modes are described as follows: 

•

Sleep mode uses interrupt control logic to allow any interrupt condition to wake the 
processor. As the MCF5272 is fully static, sleep mode is simply the disabling of the 
core’s clock after the current instruction completes. An interrupt from any internal 
or external source causes on-chip power management logic to reenable the core’s 
clock; execution resumes with the next instruction. This allows rapid return from 
power-down state as compared to a dynamic implementation that must perform 
power-on reset processing before software can handle the interrupt request. If 
interrupts are enabled at the appropriate priority level, program control passes to the 
relevant interrupt service routine.

•

Stop mode is entered by the disabling of the external clock input and is achieved by 
software setting a bit in a control register. Program execution stops after the current 
instruction. In stop mode, neither the core nor peripherals are active. The MCF5272 
consumes very little power in this mode. To resume normal operation, the external 
interrupts cause the power management logic to re-enable the external clock input. 
The MCF5272 resumes program execution from where it entered stop mode (if no 
interrupt are pending), or starts interrupt exception processing if interrupts are 
pending.

 

1.2.2.5  Parallel Input/Output Ports

 

The MCF5272 has up to three 16-bit general-purpose parallel ports, each line of which can
be programmed as either an input or output. Some port lines have dedicated pins and others
are shared with other MCF5272 functions. Some outputs have high drive current capability. 

 

1.2.2.6  Interrupt Inputs

 

The MCF5272 has flexible latched interrupt inputs each of which can generate a separate,
maskable interrupt with programmable interrupt priority level and triggering edge (falling
or rising). Each interrupt has its own interrupt vector.

 

1.2.3  UART Module

 

The MCF5272 has two full-duplex UART modules with an on-chip baud rate generator
providing both standard and non-standard baud rates up to 5 Mbps. The module is
functionally equivalent to the MC68681 DUART with enhanced features including 24-byte
Tx and Rx FIFOs. Data formats can be 5, 6, 7, or 8 bits with even, odd, or no parity and up

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
Pima ZEL508 Installation Instructions preview
ZEL508
Brand: Pima Pages: 4
Fostex DE-1 Service Manual preview
DE-1
Brand: Fostex Pages: 20
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
AXIOMTEK AIE900-XNX Series User Manual preview
AIE900-XNX Series
Brand: AXIOMTEK Pages: 53
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Idis DR-1508P Operation Manual preview
DR-1508P
Brand: Idis Pages: 85
Mitsubishi 32172 User Manual preview
32172
Brand: Mitsubishi Pages: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Brand: Mellanox Technologies Pages: 57
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
Nakayo NYC-16VDSL-B Instruction & Installation Manual preview
NYC-16VDSL-B
Brand: Nakayo Pages: 119
Omron JUSP-NS500 Datasheet preview
JUSP-NS500
Brand: Omron Pages: 6
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Brand: Rolls Pages: 1
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Brand: Cypress Semiconductor Pages: 19
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Brand: ekwb Pages: 2

Brands by name

Popular brands

Load more brands