manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

19-22

MCF5272 User’s Manual

 

UART0 Module Signals and PB[4:0]  

pin. After reset all pins multiplexed with GPIO signals default to inputs.

Port A general purpose I/O, PA[15:8] are multiplexed with PLIC TDM port 1 pins.

Port A general purpose I/O, PA[6:0] are multiplexed with USB module signals. PA7 is
multiplexed with QSPI_CS3 and DOUT3.

Port B general purpose I/O, PB[4:0] are multiplexed with the UART0 interface pins. If the
UART0 interface is enabled, PB[4:0] are unavailable. PB5 is multiplexed with TA. PB6 is
dedicated. PB7 is multiplexed with TOUT0.

Port B general purpose I/O, PB[15:8] are multiplexed with the Ethernet interface pins. If
the Ethernet interface is enabled, PB[15:8] are unavailable.

Port C general purpose I/O, PC[15:0] are multiplexed with D[15:0]. When 32-bit wide bus
mode is selected, port C is unavailable.

19.9  UART0 Module Signals and PB[4:0]

The UART0 module uses the signals in this section for data and clock signals. 

These signals are multiplexed with the GPIO port B signals PB[4:0].

19.9.1  Transmit Serial Data Output (URT0_TxD/PB0)

UART0 mode: URT0_TxD is the transmitter serial data output for the UART0 module. The
output is held high (mark condition) when the transmitter is disabled, idle, or in the local
loopback mode. Data is shifted out, lsb first, on this pin at the falling edge of the serial clock
source.

Port B mode: This pin can also be configured as the PB0 I/O.

19.9.2  Receive Serial Data Input (URT0_RxD/PB1)

UART0 mode: URT0_RxD is the receiver serial data input for the UART0 module. Data
received on this pin is sampled on the rising edge of the serial clock source lsb first. When
the UART0 clock is stopped for power-down mode, any transition on this pin restarts it.

Port B mode: This pin can also be configured as the PB1 I/O.

19.9.3  Clear-to-Send (URT0_CTS/PB2)

UART0 mode: Asserting the URT0_CTS input is the clear-to-send (CTS) input, indicating
to the UART0 module that it can begin data transmission.

Port B mode: This pin can also be configured as the PB2 I/O.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

TC Electronic ATAC Service Manual preview
ATAC
Brand: TC Electronic Pages: 55
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Brand: Zenith Data Systems Pages: 64
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
Devolo Magic WiFi mini Ek Manual preview
Magic WiFi mini Ek
Brand: Devolo Pages: 22
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Brand: Accom Pages: 15
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
ETAS BR-XETK-S4.0 User Manual preview
BR-XETK-S4.0
Brand: ETAS Pages: 82
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
Nakayo NYC-16VDSL-B Instruction & Installation Manual preview
NYC-16VDSL-B
Brand: Nakayo Pages: 119
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Brand: TRENDnet Pages: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Brand: Radio Shack Pages: 1
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Brand: Idis Pages: 16
ZIMO MXULFA Instruction Manual preview
MXULFA
Brand: ZIMO Pages: 13
Xtreme SNMP-2PV2 User & Installation Manual preview
SNMP-2PV2
Brand: Xtreme Pages: 83
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Brand: YASKAWA Pages: 87
Boser HS-2605 Manual preview
HS-2605
Brand: Boser Pages: 82
Williams Sound DW SY 1 User Manual preview
DW SY 1
Brand: Williams Sound Pages: 2

Brands by name

Popular brands

Load more brands