Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 310 | Manualshive

Page: 310 / 550

background image

13-16

MCF5272 User’s Manual

PLIC Registers

13.5 PLIC Registers

Any bits in the following registers marked 0 have no function. When the register is a
read/write register, these bits should be cleared.

Some registers are described that control more than one port. In these cases, parentheses
indicates to which port the control bits relate; for example, LM0(0) is the LM0 bit for
port 0.

13.5.1 B1 Data Receive Registers (P0B1RR–P3B1RR)

All bits in these registers are read only and are set on hardware or software reset.

The PnB1RRs contain the last four frames of data received on channel B1. (P0B1RR is the
B1 channel data for port 0, P1B1RR is B1 for port 1, and so on.) The data are packed from
the least significant byte (LSB), up to the most significant byte (MSB).

These registers are aligned on longword boundaries from MBAR + 0x300 for P0B1RR to
MBAR + 0x30C for P3B1RR. See Section 13.2.3, “GCI/IDL B- and D-Channel Bit
Alignment,” for the frame and bit alignment within the 32-bit word.

0x036C

Port2 GCI monitor Tx (P2GMT)

Port3 GCI monitor Tx (P3GMT)

0x0370

Reserved

GCI monitor Tx status

(PGMTS)

GCI monitor Tx abort

(PGMTA)

Reserved

0x0374

Port0 GCI C/I Rx

(P0GCIR)

Port1 GCI C/I Rx

(P1GCIR)

Port2 GCI C/I Rx

(P2GCIR)

Port3 GCI C/I Rx

(P3GCIR)

0x0378

Port0 GCI C/I Tx

(P0GCIT)

Port1 GCI C/I Tx

(P1GCIT)

Port2 GCI C/I Tx

(P2GCIT)

Port3 GCI C/I Tx

(P3GCIT)

0x037C

Reserved

GCI C/I Tx status

(PGCITSR)

0x0380

GCI C/I D-Channel

status (PDCSR)

0x0384

Port0 periodic status (P0PSR)

Port1 periodic status (P1PSR)

0x0388

Port2 periodic status (P2PSR)

Port3 periodic status (P3PSR)

0x038C

Aperiodic Interrupt status register (PASR)

Reserved

Loop back Control

(PLCR)

0x0390

Reserved

D-Channel Request (PDRQR)

0x0394

Port0 Sync Delay (P0SDR)

Port1 Sync Delay (P1SDR)

0x0398

Port2 Sync Delay (P2SDR)

Port3 Sync Delay (P3SDR)

0x039C

Reserved

Clock Select (PCSR)

Table 13-1. PLIC Module Memory Map (Continued)

MBAR

Offset

[31:24]

[23:16]

[15:8]

[7:0]

«
...
308
309
310
311
312
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Brand: Salus Pages: 16

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

Brand: Amperes Pages: 8

Brand: Supermicro Pages: 16

Brand: FDI Pages: 2

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

Brand: ZALMAN Pages: 16

Brand: XMOS Pages: 8

Brand: Rosewill Pages: 5

Brand: IBM Pages: 78

Brand: Intel Pages: 469

Brand: Zhone Pages: 494

Brand: NetApp Pages: 28

Brand: NetApp Pages: 10

Brand: GE Pages: 24

0150-0241 ProBridge

Brand: GE Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands