manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  10.  DMA Controller  

10-5

DMA Controller Registers

10.3.3  DMA Source Address Register (DSAR)

The DSAR provides a 32-bit address, which the DMA controller drives onto the internal
address bus for all of the channel’s read accesses. The address value is altered after each
read access according to the addressing mode.

11

ASCEN

Address sequence complete interrupt enable. 
0 ASC interrupt is disabled.
1 ASC interrupt is enabled.

10

—

Reserved, should be cleared. 

9

TEEN

Transfer error interrupt enable. 
0 TE interrupt is disabled.
1 TE interrupt is enabled.

8

TCEN

Transfer complete interrupt enable. 
0 TC interrupt is disabled.
1 TC interrupt is enabled.

7–5

—

Reserved, should be cleared. 

4

INV

Invalid combination.
0 No invalid combination detected.
1 An invalid combination of request and address modes is programmed into the mode register. 

INV remains set until it is cleared by writing a 1 to it or by a hardware reset. Writing a 0 has no 
effect. No further transfers can take place when this bit is set.

3

ASC

Address sequence complete. 
0 Address sequence is not complete.
1 The address sequence is complete. This occurs when the byte counter decrements to 0. 

Corresponds to DMA complete. ASC remains set until it is cleared by writing a 1 to its location 
or by a hardware reset. Writing a 0 has no effect. No further transfers can take place when ASC 
is set. It is important to ensure that the combination of source address, destination address, and 
transfer sizes ensures that the byte counter always decrements to 0.

2

—

Reserved, should be cleared. 

1

TE

Transfer error. 
0 No transfer error.
1 A DMA data transfer terminated with an error such as an internally generated bus error. This 

generally occurs when the address is not decoded successfully by an on-chip peripheral or by a 
chip select register. TE remains set until it is cleared by writing a 1 to its location or by a 
hardware reset. Writing 0 has no effect. No further transfers can take place when TE is set.

0

TC

Transfer complete. 
1 A data transfer completed successful. The bit is cleared when DMA module is reset. Writing a 0 

to this location has no effect. This bit is available to show that the DMA transfers have started. 
Otherwise it is not essential to monitor the status of this bit.

Table 10-3. DIR Field Descriptions (Continued)

Bits Name 

Description

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Brand: XMOS Pages: 112
Paradyne COMSPHERE 3610 User Manual preview
COMSPHERE 3610
Brand: Paradyne Pages: 112
CSS SafetyNet Quick Install Manual preview
SafetyNet
Brand: CSS Pages: 2
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
AMC DSP 88 User Manual preview
DSP 88
Brand: AMC Pages: 28
Homeworks HQP7-RF-2 Installation Instructions Manual preview
HQP7-RF-2
Brand: Homeworks Pages: 24
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Brand: S&T Pages: 115
Intel Braswell Series Technical Manual preview
Braswell Series
Brand: Intel Pages: 54
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Brand: 7th Sense Pages: 148

Brands by name

Popular brands

Load more brands