manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  9.  SDRAM Controller  

9-17

SDRAM Interface

•

16-byte read or write bursts during Ethernet DMA transfers to/from SDRAM with 
access times of n-1-1-1 or n-1-1-1-1-1-1-1 depending on 32 or 16 bit SDRAM port 
width as described in the previous two paragraphs.

These SDRAM accesses are shown in Figure 9-9 through Figure 9-15. The SDRAM
supports a low-power, self-refreshing sleep mode as shown in Figure 9-14 and Figure 9-15.
It is also possible to turn off the SDRAM controller completely using the power
management control register in the SIM.

Figures show burst read and burst writes, with a page miss and a page hit for each case. A
single-cycle read or write is identical to the first access of a burst. In normal operation the
SDRAM controller refreshes the SDRAM. 

As these examples show, SDCLKE is normally high and SDCLK is always active.
SDCLKE can be forced to 0 and SDCLK can be shut off by putting the SDRAM controller
into power down or self-refresh mode.

9.10.1  SDRAM Read Accesses

The read examples, Figure 9-9 and Figure 9-10, show a CAS latency of 2, SDCR[REG] = 0
and SDCR[INV] = 1. 

In T1, the ColdFire core issues the address. This cycle is internal to the device and always
occurs. In T2, the SDRAM controller determines if there is a page miss or hit. This cycle is
internal to the device and always occurs.

Because Figure 9-9 shows a page miss, the 

PRECHARGE

 command (T3) and the following

cycle occur. During precharge the SDRAM writes the designated on-chip RAM page buffer
back into the SDRAM array. The number of cycles for a precharge is set by programming
SDTR[RP]. The default after reset is two cycles. The activate new page cycle that follows
(T5) is required to open a new page due to the page miss. Cycle T6 is a wait state for
SDRAM activation command. It is added due to default value of 0b01 in SDTR[RCD]. For
lower clock speed systems the RCD value could be written as 00 and this clock cycle can
be removed. Consult the data sheets of the SDRAM devices being used.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
Paradyne COMSPHERE 3800 Series Release Note preview
COMSPHERE 3800 Series
Brand: Paradyne Pages: 88
Paradyne COMSPHERE 3800PLUS Supplementary Manual preview
COMSPHERE 3800PLUS
Brand: Paradyne Pages: 5
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Brand: NXP Semiconductors Pages: 54
Harman crown PIP Series Reference Manual preview
crown PIP Series
Brand: Harman Pages: 16
Lindy 32116 User Manual preview
32116
Brand: Lindy Pages: 12
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Brand: Riverbed Pages: 140
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Brand: Genexis Pages: 7
Rajant BreadCrumb ES1 User Manual preview
BreadCrumb ES1
Brand: Rajant Pages: 93
IBASE Technology SI-22-415 User Manual preview
SI-22-415
Brand: IBASE Technology Pages: 49
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Brand: Patton electronics Pages: 80
Stepper Motor Canada DB25-1R5AM Manual preview
DB25-1R5AM
Brand: Stepper Motor Canada Pages: 7

Brands by name

Popular brands

Load more brands