manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

5-16

MCF5272 User’s Manual 

 

Background Debug Mode (BDM)  

5.5.1  CPU Halt

Although most BDM operations can occur in parallel with CPU operations, unrestricted
BDM operation requires the CPU to be halted. The sources that can cause the CPU to halt
are listed below in order of priority:

1. A catastrophic fault-on-fault condition automatically halts the processor.

2. A hardware breakpoint can be configured to generate a pending halt condition 

similar to the assertion of BKPT. This type of halt is always first made pending in 
the processor. Next, the processor samples for pending halt and interrupt conditions 
once per instruction. When a pending condition is asserted, the processor halts 
execution at the next sample point. See Section 5.6.1, “Theory of Operation.” 

3. The execution of a HALT instruction immediately suspends execution. Attempting 

to execute HALT in user mode while CSR[UHE] = 0 generates a privilege violation 
exception. If CSR[UHE] = 1, HALT can be executed in user mode. After HALT 
executes, the processor can be restarted by serial shifting a 

GO

 command into the 

debug module. Execution continues at the instruction after HALT.

4. The assertion of the BKPT input is treated as a pseudo-interrupt; that is, the halt 

condition is postponed until the processor core samples for halts/interrupts. The 
processor samples for these conditions once during the execution of each 
instruction. If there is a pending halt condition at the sample time, the processor 
suspends execution and enters the halted state.

The assertion of BKPT should be considered in the following two special cases:

•

After the system reset signal is negated, the processor waits for 16 processor clock 
cycles before beginning reset exception processing. If the BKPT input is asserted 
within eight cycles after RSTI is negated, the processor enters the halt state, 
signaling halt status (0xF) on the PST outputs. While the processor is in this state, 
all resources accessible through the debug module can be referenced. This is the 
only chance to force the processor into emulation mode through CSR[EMU]. 

After system initialization, the processor’s response to the 

GO

 command depends on 

the set of BDM commands performed while it is halted for a breakpoint. 
Specifically, if the PC register was loaded, the 

GO

 command causes the processor to 

exit halted state and pass control to the instruction address in the PC, bypassing 
normal reset exception processing. If the PC was not loaded, the 

GO

 command 

causes the processor to exit halted state and continue reset exception processing.

•

The ColdFire architecture also handles a special case of BKPT being asserted while 
the processor is stopped by execution of the STOP instruction. For this case, the 
processor exits the stopped mode and enters the halted state, at which point, all BDM 
commands may be exercised. When restarted, the processor continues by executing 
the next sequential instruction, that is, the instruction following the STOP opcode.

CSR[27–24] indicates the halt source, showing the highest priority source for multiple halt
conditions. 

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
SurfControl 509-8629-00 Setup Manual preview
509-8629-00
Brand: SurfControl Pages: 2
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
AXIOMTEK CEM820 Series User Manual preview
CEM820 Series
Brand: AXIOMTEK Pages: 58
Comelit IPNVR004BPOE Manual preview
IPNVR004BPOE
Brand: Comelit Pages: 19
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Brand: Bose Pages: 2
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Brand: Lattice Semiconductor Pages: 28
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Brand: PairGain Pages: 7
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Brand: Genexis Pages: 7
Mitsubishi M16C/20 Series Software Manual preview
M16C/20 Series
Brand: Mitsubishi Pages: 188
ZALMAN CNPS10X Flex User Manual preview
CNPS10X Flex
Brand: ZALMAN Pages: 12
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Brand: Boardcon Embedded Design Pages: 36
HIKVISION DS-7600NI-H2/4P Series Installation Manual preview
DS-7600NI-H2/4P Series
Brand: HIKVISION Pages: 14
National Datacomm 9210S01 User Manual preview
9210S01
Brand: National Datacomm Pages: 62
Extron electronics DVI Output Card Installation Manual preview
DVI Output Card
Brand: Extron electronics Pages: 6

Brands by name

Popular brands

Load more brands