Motorola Avigilon ACC VMA-RPA-RGD-8P2 User Manual Download Page 20 | Manualshive

Page: 20 / 46

background image

l

PoE

. See:

l

Assigning a PoE Power Budget

l

Budgeting PoE Power

l

Logs

. See

Providing Device Logs for Support

Viewing PoE Port Status

The PoE panel displays a status for each port in the Status column. Statuses include the following:

Green

Powered

A PoE device is connected to the port and is operating normally.

High
powered

PoE+ is turned on.

Gray

Disconnected There is no device connected to the port.

Unpowered

The PoE port power is switched off from the PoE page in the ACC ES Admin
Web UI

Yellow Overloaded

A PoE device is connected to the port but is not receiving power. This status
typically occurs when one port is overcurrent, or the device is requesting more
power than budgeted, etc.

Low current

The device is getting low current from the port.

Red

Error

The device is in an error state.

Tip:

If a camera is disconnected then reconnected to the device, you may need to refresh this page

to view the latest status and budget values.

Viewing PoE Port Status

20

«
...
18
19
20
21
22
...
»

Summary of Contents for Avigilon ACC VMA-RPA-RGD-8P2















































Reviews:

No comments

Related manuals for Avigilon ACC VMA-RPA-RGD-8P2

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: H3C Pages: 34

Brand: Yamaha Pages: 4

Brand: Lab.gruppen Pages: 35

Brand: Lattice Semiconductor Pages: 15

Brand: Pakedge Device & Software Pages: 20

Brand: National Instruments Pages: 11

EK-Vector Radeon RX5700 + XT Backplate

Brand: ekwb Pages: 7

Brand: Google Pages: 14

Brand: Amplifier Tech Pages: 36

Brand: H3C Pages: 26

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

IPLink 2603 Series

Brand: Patton Pages: 120

Aquaduct 240 eco

Brand: Aqua Computer Pages: 20

Brand: Lantronix Pages: 75

Brand: METREL Pages: 21

Brand: SMC Networks Pages: 68

Brand: Ubiquiti Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands