Motorola APX8500 Manual Download Page 87

Page: 87 / 273

NEXT >

< PREV

CONTENTS

ADVANCED FEATURES

(continued)

Making a Selective Call

Procedure:

[Preprogrammed Button]

Press the preprogrammed

Selective Call

button

to dial the preprogrammed ID.

Press and hold the

PTT

button to start the

Selective Call.

The display shows the ID of the target radio.

Release the PTT button to listen.

[Menu]

From the home screen, scroll

left

right

Call

Press the

Menu Select

button directly below

Call

The display shows the last transmitted or received
ID.

Press the

Menu Select

button directly below

Cnts

to scroll through and select the required ID.

Scroll

down

to the required ID.

Use the keypad to enter the required ID.

Press and hold the

PTT

button to start the

Selective Call.

The display shows the ID of the target radio.

Release the PTT button to listen.

Press the

Home

button to hang up. If you do not

hang up, your radio will remain in Selective Call state
with the other unit. You will miss all sub-fleet traffic
and incoming phone calls.

DEMO

Summary of Contents for APX8500


















































































































































































































































































Search results

Summary of Contents for APX8500

Reviews:

Motorola APX8500, Manual, Page: 87 / 273

Search results

Summary of Contents for APX8500

Reviews: