Motorola APX8500 Manual Download

Page: 75 / 273

NEXT >

< PREV

CONTENTS

GENERAL RADIO OPERATION

(continued)

[Menu]

From the home screen, scroll

left

right

Call

Press the

Menu Select

button directly below

Call

The display shows the last transmitted or received ID.

Press the

Menu Select

button directly below

Cnts

to scroll through and select the required ID.

Press the

Menu Select

button directly below

List

to go to the first number of the call list.

Scroll

down

and select the required ID.

Use the keypad to enter the required ID.

Press the

PTT

button to start the Private Call.

The display shows

Calling... <Number> OR Calling… <Alias>

Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth.

When you are connected, the display shows the ID of the target radio.

If no acknowledgement is received, the display shows

No acknowledge

If the target radio does not respond before the time out, the display shows

No answer

Press and hold the

PTT

button to talk. Release the

PTT

button to listen.

Press the

Home

button to return to the home screen.

DEMO

Summary of Contents for APX8500


















































































































































































































































































Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands

Motorola APX8500, Manual

Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands