Motorola APX8500 Manual Download

Page: 153 / 273

NEXT >

< PREV

CONTENTS

ADVANCED FEATURES

Text Messaging Service (TMS)

Sending a Quick Text Message

153

Quick Text messages are messages that are
predefined and usually consist of messages that are
used most frequently.

Each Quick Text message has a maximum length of
50 characters.

Procedure:

[Preprogrammed Button]

To access this feature using the preprogrammed
button, press the preprogrammed

Quick Text

button

Scroll

down

to scroll through the list of

messages and press the

Menu Select

button

directly below

Sel

to select the required message.

The message appears on the

Compose

screen,

with a blinking cursor at the end of ti. Use the

keypad

to edit the message, if required.

Press the

Menu Select

button directly below

Optn

Scroll

down

Send Message

and press

the

Menu Select

button directly below

Sel

Scroll

down

through the address list and

select the required address. The message is sent
after the address is selected.

Scroll

down

[Other Recpnt]

and press

the

Menu Select

button below

Edit

. When a

blinking cursor appears in the

Enter Address

screen, use the

keypad

to type the address entry.

Press the

Menu Select

button directly below

Send

or press the PTT button to send the

message.

Summary of Contents for APX8500


















































































































































































































































































Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands

Motorola APX8500, Manual

Search results

Summary of Contents for APX8500

Reviews:

Related manuals for APX8500

Brands by name

Popular brands