manualshive.com logo in svg

Motorola 56F8323, User Manual

Share
Download
Motorola 56F8323 User Manual Download Page 19

56F8323

MOTOROLA

Technical Summary

2-3

2.1   56F8323

The 56F8323EVM uses a Motorola MC56F8323FG60 part, designated as U1 on the board 
and in the schematics. This part will operate at a maximum external bus speed of 60MHz. 
A full description of the 56F8323, including functionality and user information, is 
provided in these documents:

•

56F8323 Technical Data Sheet

,

 

(MC56F8323/D)

:

 Electrical and timing 

specifications, pin descriptions, device specific peripheral information and package 
descriptions (this document)

•

56F8300 Peripheral User Manual

,

 

(MC56F8300UM/AD): Detailed description of 

peripherals of the 56F8300 family of devices

•

DSP56800E Reference Manual

,

 

(DSP56800ERM/D): Detailed description of the 

56800E family architecture, 16-bit core processor, and the instruction set

Refer to these documents for detailed information about chip functionality and operation. 
They can be found on this URL:

www.motorola.com/semiconductors

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for 56F8323





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands