manualshive.com logo in svg

Motoalliance DENALI MA11748, Manual, Page: 1 / 5

Share
Download
Motoalliance DENALI MA11748 Manual Download Page 1

866.527.7637 

1 

[email protected]

 

 

 

23001 Industrial Blvd, Rogers, MN  55374 / 1-866-527-7637 

www.motoalliance.com 

 

DENALI Plow Mount 

MA11748 

Can-Am Defender 

 

Thank you for purchasing a DENALI plow mount. You now own a premium, custom 
plow mount to allow you to use your plow with your UTV/SxS. Please note the following 
instructions and heed all warnings.  

  Your UTV/SxS and/or plow system can cause death or injury. Please use caution 

and common sense when operating your unit. 

  Read your Plow Operator Manual, your Winch Operator Manual, and all warning 

labels before operating your UTV/SxS. 

  Operate your UTV/SxS at a walking speed with the blade installed. Do not 

exceed 5 mph (8 km/h) even with the blade up. 

  Do not operate the UTV/SxS on slopes greater than 10 degrees with the plow 

installed. 

  Always lower the plow to the down position before leaving your UTV/SxS 

unattended. 
 

SEVERE INJURY OR DEATH MAY RESULT IF YOU ARE NEGLIGENT.   
 
 
 
 
 
 

Summary of Contents for DENALI MA11748






Reviews:

No comments