![Motion Control Engineering Motion 4000 Manual Download Page 337](http://html1.mh-extra.com/html/motion-control-engineering/motion-4000/motion-4000_manual_1837882337.webp)
Status and Error Messages
5-15
5
Motion 4000
HOISTWAY DOOR BYPASS SW. FAILURE
Description:
The expected input logic from the HOISTWAY DOOR BYPASS switch has failed.
Troubleshooting:
1. Cycle the HC-CTL board hoistway door bypass switch a few times to exercise it. Verify that it is fully in
the ON or OFF position.
2. Verify 2S and DLAB connections and wiring.
HOISTWAY SAFETY DEVICE OPEN
Description:
One of the hoistway safety devices has activated, opening the safety circuit (e.g., pit stop
switch, car and counterweight buffer switches, up/down final limit switches).
Troubleshooting:
Check all hoistway safety devices. Refer to controller wiring prints for applicable
devices. Verify that the SAFH terminal on the HC-CTL board is powered.
HOSPITAL PHASE 1 OPERATION
Description:
A hospital emergency call switch is activated.
Troubleshooting:
Check that the hospital emergency operation option is set correctly. If hospital emer-
gency operation is not required, set to no. If required, set floors eligible to answer a hospital call to yes.
HOSPITAL PHASE 2 OPERATION
Description:
The car has answered a hospital emergency call or the in-car hospital emergency key switch
has been activated (HOSP is high).
Troubleshooting:
Check that the hospital emergency operation option is set correctly, then check to see if
any spare inputs are programmed as HOSP and if they are activated.
ICPD INPUT FAILURE
Description:
The Car Panel Inspection Down (ICPD) input is high while the 2 bus is low.
Troubleshooting:
1. Check for incorrect wiring or short on the HC-CTL board ICPD input and 2 bus.
ICPU INPUT FAILURE
Description:
The Car Panel Inspection Up (ICPU) input is high while the 2 bus is low.
Troubleshooting:
1. Check for incorrect wiring or short on the HC-CTL board ICPU input and 2 bus.
ICTD INPUT FAILURE
Description:
The Car Top Inspection Down (ICTD) input is high while the SAFH bus is low.
Troubleshooting:
1. Check for incorrect wiring or short on the HC-CTL board ICTD input.
ICTU INPUT FAILURE
Description:
The Car Top Inspection Up (ICTU) input is high while the SAFH bus is low.
Troubleshooting:
1. Check for incorrect wiring or short on the HC-CTL board ICTU input.
INA INPUT FAILURE
Description:
The INA (COP access enable switch) input did not receive a signal when expected.
Troubleshooting:
1. Check for incorrect wiring or short on the HC-CTL board INA input and 2 bus.
2. Check access enable switch in COP and connection through traveler.
IN-CAR INSPECTION
Description:
The controller is currently on IN-CAR inspection, activated by 120VAC at screw terminal INCP
on the HC-CTL board.
IN CAR STOP SWITCH ACTIVATED
Description:
The in-car stop switch has been pulled, opening the safety circuit.
Troubleshooting
: Check the status of the in-car emergency stop switch.
Table 5.1 Status and Error Messages
Scrolling Message - Special Event Message
Summary of Contents for Motion 4000
