Status and Error Messages
5-13
5
Motion 4000
FIRE SERVICE PHASE 1 - MAIN
Description:
The car is returning to the main fire return landing. The FRS input is low or the FRON or
FRON2 inputs are high.
Troubleshooting:
Inspect fire sensors and Fire Phase I switch wiring. For some fire codes, including
ASME, the Fire Phase I switch must be turned to the
BYPASS
position and then back to
OFF
to clear the fire
service status once activated.
FIRE SERVICE PHASE 2
Description:
The FCS controller input is
ON.
Troubleshooting:
Inspect the phase 2 switch and wiring. In some cases, to exit Fire Service Phase 2, the
car must be at the fire floor at which Fire Phase 2 was activated, the doors must be fully open, and the
phase 2 switch must be off (the FCOFF input must be activated) to exit phase 2.
FRONT DOL AND DLK ARE BOTH ACTIVE
Description:
A critical failure has caused both the Door Open Limit and Door Lock inputs to be active at
the same time.(DOL=0 & DLK=1). There is a problem with DOL and/or DLK circuitry or wiring.
Troubleshooting:
Inspect the Door Open Limit and the Door Lock circuitry and wiring. When this error is
generated, the car will shut down with the doors open and will not answer any calls. The only way to reset
this error condition is to put the car on Inspection operation.
FRONT DOOR FAILED TO CLOSE
Description:
Doors Open (DCL = 1). There is a problem with DCL circuitry or wiring.
Troubleshooting:
Inspect the Door Closed Limit circuitry and wiring. When this error is generated, the car
is not allowed to run.
FRONT DOOR IS LOCKED BUT NOT FULLY CLOSED
Description:
Doors Open (DCL = 1) and Locked (DLK = 1). There is a problem with DCL and/or DLK cir-
cuitry or wiring.
Troubleshooting:
Inspect the Door Closed Limit and the Door Lock circuitry and wiring. When this error is
generated, the car is not allowed to run.
FRONT DOOR LOCK SWITCH FAILURE
Description:
The front door lock contacts have failed closed.
Troubleshooting:
Ensure that, with the front hoistway doors closed and locked, there is power on the DLS
input and no power present on the DCL input.
FRONT DOOR OPEN LIMIT FAILURE
Description:
The door open limit switch has failed open.
Troubleshooting:
Ensure that the car gate is open, there is no power on the DOL input, and no power
present on the DLS or CD inputs.
FRONT DZ RELAY DISCREPANCY
Description:
HC-CTL door zone input and door zone flag from TC-MPI board do not match. The elevator
will stop at the next floor in the direction of travel and shut down until the fault is cleared (HC-CTL fault
reset or toggle Inspection switch).
Troubleshooting:
1. Verify door zone (virtual if ELGO system, magnet if LS-EDGE) input. Reset A, B, and C processors on
TC-MPI board.
2. Verify connection between MPI board DZFO and CTL board DZF.
FRONT GATE SWITCH FAILURE
Description:
The front car gate switch has failed closed.
Troubleshooting:
Ensure that, with the front car gate closed, there is power on the GS input and no
power present on the DCL input.
Table 5.1 Status and Error Messages
Scrolling Message - Special Event Message
Summary of Contents for Motion 4000
